
The AirTAC SAIJ80 Adjustable Cylinder SAIJ80X60-40 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø80mm bore and 60mm stroke, G3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ80X60-40 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that allows you to trim the effective travel down from 60 mm to a 20 mm minimum. The carbon steel piston rod and M20x1.5 rod thread provide robust load handling, though long unsupported strokes still require external guide rails.
Unlike a fixed-stroke SAI cylinder, this model uses a rear stopper screw to fine-tune the end position at commissioning without swapping hardware. The adjuster acts solely as a travel stop and works alongside the variable air cushions at both ends to decelerate the load; it does not lock or hold the load without live air pressure. For load-holding requirements, consider the SAIL or BSAI series instead. The extruded aluminum barrel includes sensor grooves on both sides, ready for CMSE reed or DMSE electronic switches if a magnet is added later.
| Model | Airtac SAIJ80 Adjustable Cylinder SAIJ80X60-40 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 60 mm |
| Acting type | Double acting |
| Port size | G3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2268 N | 2268 N |
| 0.7 MPa | 3175 N | — |
| Max (@1.0 MPa) | 463 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact end-position from 20 to 60 mm during product size transitions without physically swapping the cylinder or adding external mechanical stops.
Fine-tune the clamping or pressing travel window on the fly, using the rear stopper to perfect the stroke distance during initial machine commissioning.
Choose this SAIJ80X60-40 when a machine setup requires a highly variable end-stop within a compact 60 mm nominal stroke, yielding a usable 20-60 mm travel window. If your application needs less force, stepping down to a 63 mm bore provides 1402 N of pull force at 0.5 MPa, while stepping up to a 100 mm bore offers 3681 N of pull force for heavier loads. Because the stroke is under 300 mm, side-load risks are lower, but you should still ensure the load is guided to prevent rod binding.
To match this cylinder exactly as an ISO 15552 replacement, specify an 80 mm bore, 60 mm stroke, 40 mm adjustment range, PT tapered port threads, and the Basic, FA, LB, TC, FTC, TCM1, or TCM2 mounting set (FB, CA, CB, and CR are omitted). This standard configuration uses a carbon steel rod and no magnet; add an -S suffix if you require electronic or reed sensor feedback.
Quick checklist
At the maximum pressure of 1.0 MPa, it delivers up to 513 kgf.
The rear adjuster screw allows you to shorten the 60 mm nominal stroke by up to 40 mm, creating a usable travel window of 20 to 60 mm. This stopper only sets the end position and decelerates the load; it does not hold the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.