Airtac SC100 Standard Cylinder SC100X130
The AirTAC Airtac SC100 Standard Cylinder SC100X130 is a genuine double-acting standard air cylinder with a Ø100mm bore and 130mm stroke, PT1/2 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ100 mm
- Stroke130 mm
- Port sizePT1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 29 mm
About the Airtac SC100 Standard Cylinder SC100X130
The AirTAC SC100X130 is a double-acting tie-rod cylinder that generates 3927 N of push force at 0.5 MPa (up to 7068 N at 0.9 MPa). With a 130 mm stroke and a 25 mm diameter piston rod, it suits medium-reach clamping and pressing tasks where a compact retracted length is needed.
This model has a body length A of 188 mm and an adjustable air cushion of 29 mm at each end to decelerate the piston smoothly. The standard PT1/2 ports and M20x1.5 rod thread make it straightforward to plumb and connect tooling.
Airtac SC100 Standard Cylinder SC100X130 Technical Specifications
| Model | Airtac SC100 Standard Cylinder SC100X130 |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø100 mm |
| Stroke | 130 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (approx.) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC100 Standard Cylinder SC100X130
| SC | Standard tie-rod cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×130 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC100 Standard Cylinder SC100X130 Is Used
Pallet Stop & Lift
The 3927 N push force at 0.5 MPa is ideal for raising or stopping heavy pallets on conveyor lines, providing a firm 130 mm lift stroke.
Heavy-Duty Clamping
Use the SC100X130 in welding or assembly fixtures where a powerful, consistent clamp force is needed to hold large workpieces during processing.
Press-Fit Assembly
With up to 7068 N of force at 0.9 MPa, this cylinder can drive press-fit operations for bearings or bushings into housings over a controlled 130 mm distance.
Is the Airtac SC100 Standard Cylinder SC100X130 the Right Cylinder?
Choose the SC100 bore when your load needs roughly 3900 N of push force at typical shop air pressure. If you can accept a smaller footprint, the SC80 bore delivers 2513 N at 0.5 MPa; for heavier work, the SC125 bore steps up to 6136 N at the same pressure. Always match bore, 130 mm stroke, PT1/2 port thread, and the basic mounting configuration when replacing an existing cylinder.
At 130 mm stroke the rod is well supported inside the barrel, but any side load should still be managed with an external guide or linear rail to protect the rod bearing and seals from premature wear.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC100 Standard Cylinder SC100X130 FAQ
At 0.5 MPa the push force is 3927 N and the pull force is 3681 N. At the maximum operating pressure of 0.9 MPa, the push force reaches 7068 N. The theoretical maximum at 1.0 MPa is 801 kgf.
No. The SC series is a tie-rod cylinder and is physically shorter than an ISO 15552 profile cylinder, so it is not dimensionally interchangeable. It replaces another AirTAC SC100 cylinder of the same stroke, port thread, and mounting style.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC100 Standard Cylinder SC100X130
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.