
The AirTAC SC100 Standard Cylinder SC100X2000S is a genuine double-acting standard air cylinder with a Ø100mm bore and 2000mm stroke, PT1/2 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
The AirTAC SC100X2000S is a double-acting pneumatic cylinder engineered for applications demanding an exceptionally long 2000 mm stroke from a 100 mm bore. This model generates a substantial push force of 3927 N at 0.5 MPa, scaling up to 7068 N at the maximum operating pressure of 0.9 MPa. The built-in magnet (-S suffix) allows direct mounting of CMSG, DMSG, or EMSG reed and solid-state sensors along the barrel for precise, contactless position feedback.
Given the stroke length, careful installation is critical. The 25 mm diameter piston rod and 29 mm adjustable air cushion at each end help manage the high kinetic energy at end-of-travel. As a non-standard stroke exceeding the 1500 mm maximum, this is a made-to-order item. The body length A is 188 mm, resulting in a total extended length of approximately 2188 mm, and it uses a PT1/2 port with an M20x1.5 rod thread.
| Model | Airtac SC100 Standard Cylinder SC100X2000S |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø100 mm |
| Stroke | 2000 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (approx.) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SC | Standard tie-rod cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×2000 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Ideal for pushing heavy pallets or large components off a conveyor line where a 2000 mm stroke is needed to clear the transfer zone completely.
Positions a heavy welding fixture or clamp arm over a long distance. The built-in magnet provides end-of-stroke confirmation to the PLC via DMSG sensors.
Provides the long linear motion to open and close a large slide gate on a silo or hopper, delivering 3927 N of force to overcome material friction.
Select the SC100 bore when your application requires a push force between 3927 N (at 0.5 MPa) and 7068 N (at 0.9 MPa). If your force requirement is lower, stepping down to an 80 mm bore provides 2513 N of push force at 0.5 MPa. For a 2000 mm stroke, an external guide or a guided cylinder is strongly recommended to protect the 25 mm rod from bending under side loads or its own weight when fully extended. When replacing, match five key points: 100 mm bore, 2000 mm stroke, PT1/2 port thread, the built-in magnet (-S) for sensor compatibility, and any mounting accessories.
Quick checklist
The theoretical push force at 0.5 MPa is 3927 N, and at the maximum operating pressure of 0.9 MPa it is 7068 N. The pull force on the retract stroke is slightly lower due to the rod area, providing 3681 N at 0.5 MPa.
Yes, for a 2000 mm stroke with a 25 mm rod, an external guide or a guided cylinder is strongly recommended. The long, unsupported rod is susceptible to bending and buckling under side loads or its own weight, which will cause premature seal and bearing failure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.