Airtac SC100 Standard Cylinder SC100X700SH
The AirTAC Airtac SC100 Standard Cylinder SC100X700SH is a genuine double-acting standard air cylinder with a Ø100mm bore and 700mm stroke, PT1/2 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ100 mm
- Stroke700 mm
- Port sizePT1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 29 mm
About the Airtac SC100 Standard Cylinder SC100X700SH
The SC100X700SH is a double-acting AirTAC SC tie-rod cylinder with a 100 mm bore and 700 mm stroke, equipped with a built-in magnet (-S suffix) and high-temperature Viton seals (-H suffix). At the standard 0.7 MPa operating pressure, this model produces 5497 N of push force, making it a powerful actuator for hot-environment automation tasks where standard seals would degrade.
This cylinder uses a 25 mm diameter piston rod with an M20x1.5 male thread and PT1/2 ports. The adjustable air cushion is 29 mm long, and the body length A is 188 mm. The Viton (FKM) seals shift the operating temperature range from the standard -20–+70 °C to 0–+150 °C, ensuring reliable performance in high-heat zones such as drying ovens or near molding presses.
Airtac SC100 Standard Cylinder SC100X700SH Technical Specifications
| Model | Airtac SC100 Standard Cylinder SC100X700SH |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø100 mm |
| Stroke | 700 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (approx.) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC100 Standard Cylinder SC100X700SH
| SC | Standard tie-rod cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×700 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC100 Standard Cylinder SC100X700SH Is Used
High-Temperature Material Handling
With Viton seals rated to 150°C, this cylinder reliably operates pushers, ejectors, or transfer arms inside industrial drying ovens, autoclaves, and hot-forming workstations where NBR or TPU seals would fail.
Heavy Palletising Systems
Delivering 7068 N of push force at 0.9 MPa, the SC100X700SH is ideal for palletising end-effectors that must lift and stack heavy bags, boxes, or crates with a long 700 mm vertical reach.
Foundry & Die-Casting Automation
The built-in magnet enables precise end-of-stroke sensing with CMSG/DMSG sensors, while the Viton seals withstand the radiant heat near die-casting machines, controlling core pulls or sprue cutters.
Is the Airtac SC100 Standard Cylinder SC100X700SH the Right Cylinder?
Select this 100 mm bore cylinder when your application requires a push force around 3927 N at 0.5 MPa. If your load is lighter and you can accept a smaller footprint, stepping down to an 80 mm bore (2513 N push at 0.5 MPa) may reduce air consumption. For higher force demands, a 125 mm bore model provides 6136 N at the same pressure.
For this 700 mm stroke, side-load management is critical. A long, unsupported 25 mm rod can bend under lateral forces, causing premature seal and bearing wear. Always guide the load externally with a linear rail or rod guide, or consider a guided cylinder assembly. As a direct replacement, match the 100 mm bore, 700 mm stroke, PT1/2 ports, Viton seals, and the built-in magnet for sensor compatibility.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC100 Standard Cylinder SC100X700SH FAQ
At the standard operating pressure of 0.7 MPa (7 bar), the theoretical push force on the extension stroke is 5497 N. The pull force on retraction is 3681 N, accounting for the 25 mm rod reducing the effective piston area.
Yes. The -S suffix indicates a magnet is embedded in the piston, allowing you to mount AirTAC CMSG (reed) or DMSG/EMSG (solid-state) sensors directly onto the cylinder barrel's sensor groove to detect piston position without any additional brackets.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC100 Standard Cylinder SC100X700SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.