Airtac SC100 Standard Cylinder SC100X760SH
The AirTAC Airtac SC100 Standard Cylinder SC100X760SH is a genuine double-acting standard air cylinder with a Ø100mm bore and 760mm stroke, PT1/2 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ100 mm
- Stroke760 mm
- Port sizePT1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 29 mm
About the Airtac SC100 Standard Cylinder SC100X760SH
The SC100X760SH is a double-acting pneumatic cylinder delivering a substantial push force of 3927 N at 0.5 MPa and up to 7068 N at 0.7 MPa, making it a powerful workhorse for demanding linear applications. Its 100 mm bore houses a 25 mm diameter piston rod with an M20x1.5 male thread, and the total extended body length reaches 948 mm (188 mm body plus the 760 mm stroke).
This model is configured with a built-in magnet (-S suffix) for direct mounting of CMSG/DMSG/EMSG sensors, enabling precise end-of-stroke detection. The -H suffix specifies Viton (FKM) seals, shifting the operating temperature range to 0 to +150 °C, ideal for hot environments or applications involving aggressive media. Ports are standard PT1/2 with an adjustable air cushion of 29 mm.
Airtac SC100 Standard Cylinder SC100X760SH Technical Specifications
| Model | Airtac SC100 Standard Cylinder SC100X760SH |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø100 mm |
| Stroke | 760 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (approx.) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC100 Standard Cylinder SC100X760SH
| SC | Standard tie-rod cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×760 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC100 Standard Cylinder SC100X760SH Is Used
Hot Press Actuation
The Viton seals and 0-150°C rating make this cylinder suitable for actuating platens or clamps in heated laminating, molding, or forming presses where standard seals would degrade.
Heavy Material Handling
With 3927 N of push force at 0.5 MPa, it can shift heavy bins or operate large diverters in high-temperature areas of a foundry or heat-treatment facility.
Sensor-Monitored Automation
The built-in magnet allows CMSG/DMSG sensors to provide open/closed-loop feedback to a PLC, ensuring the 760 mm stroke is fully achieved in every cycle without physical contact switches.
Is the Airtac SC100 Standard Cylinder SC100X760SH the Right Cylinder?
Selecting the SC100X760SH means matching a 100 mm bore with a 760 mm stroke for a force requirement around 4000 N at standard plant pressure. If your load is lighter, stepping down to an 80 mm bore (2513 N at 0.5 MPa) can reduce air consumption and physical size. For heavier loads, the 125 mm bore provides 6136 N at the same pressure. The 760 mm stroke is well within the 1500 mm maximum standard stroke for this bore.
For strokes exceeding 300 mm, particularly with this 25 mm rod, be mindful of side loading. An unsupported rod at full extension is susceptible to bending under lateral force. Mitigate this by ensuring the load is guided on external rails or by using a rigid alignment coupler. When replacing, match five points: 100 mm bore, 760 mm stroke, PT1/2 thread, the built-in magnet, and the Viton seal material.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC100 Standard Cylinder SC100X760SH FAQ
At the standard 0.5 MPa operating pressure, the push force is 3927 N and the pull force is 3681 N (accounting for the 25 mm rod area). At the maximum operating pressure of 0.9 MPa, the push force increases to 7068 N.
No. The SC series is a tie-rod cylinder that is physically shorter than an ISO 15552 profile cylinder. It is not dimensionally interchangeable with ISO 15552 standards. It matches other AirTAC SC cylinders or tie-rod cylinders with identical bore, stroke, PT port, magnet, and Viton seals.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC100 Standard Cylinder SC100X760SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.