Airtac SC100 Standard Cylinder SC100X760SN
The AirTAC Airtac SC100 Standard Cylinder SC100X760SN is a genuine double-acting standard air cylinder with a Ø100mm bore and 760mm stroke, PT1/2 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ100 mm
- Stroke760 mm
- Port sizePT1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 29 mm
About the Airtac SC100 Standard Cylinder SC100X760SN
The AirTAC SC100X760SN is a double-acting tie-rod cylinder delivering a robust 3927 N of push force at 0.5 MPa (7068 N at 0.9 MPa). With a 100 mm bore and a 760 mm stroke, it uses a 25 mm diameter piston rod and PT1/2 ports, making it well-suited for medium-to-heavy linear actuation tasks where consistent pneumatic power is needed.
This model includes a built-in magnet (-S suffix) for direct mounting of CMSG/DMSG/EMSG sensors, enabling precise end-of-stroke detection without external brackets. The NBR seal (-N suffix) provides reliable sealing for general industrial environments, and the total extended body length is approximately 948 mm (188 mm body length A + 760 mm stroke).
Airtac SC100 Standard Cylinder SC100X760SN Technical Specifications
| Model | Airtac SC100 Standard Cylinder SC100X760SN |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø100 mm |
| Stroke | 760 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (approx.) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC100 Standard Cylinder SC100X760SN
| SC | Standard tie-rod cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×760 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC100 Standard Cylinder SC100X760SN Is Used
Material Handling Pusher
The 3927 N push force at 0.5 MPa and 760 mm stroke are ideal for a heavy-duty conveyor divert arm, pushing boxes or pallets off a main line onto a branch conveyor.
Press-Fit Assembly Station
With 7068 N of force at 0.9 MPa, this cylinder can power a press-fit operation for bearings or bushings. The built-in magnet sensor confirms full insertion on every cycle.
Automated Palletizer Lift
Use the SC100X760SN as a layer-lifting actuator in a palletizing cell. The NBR seals are cost-effective for the clean, dry air environment, and the long stroke handles deep stack heights.
Is the Airtac SC100 Standard Cylinder SC100X760SN the Right Cylinder?
Select the SC100 when your application needs a push force around 3927 N at 0.5 MPa. If your load requires more force, step up to the SC125 bore (6136 N push at 0.5 MPa); for a lighter, more compact solution, the SC80 bore offers 2513 N. For this 760 mm stroke, ensure the load is guided and side forces are minimal—long, unsupported strokes on a 25 mm rod can experience bending under side load. Use an external guide or a guided cylinder for off-axis loads.
For a direct replacement, match these five points: 100 mm bore, 760 mm stroke, PT1/2 port thread, the built-in magnet (-S), and the basic (no bracket) mounting. This cylinder is not an ISO 15552 profile; it is a tie-rod design and is dimensionally interchangeable only with another AirTAC SC100 of the same configuration.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC100 Standard Cylinder SC100X760SN FAQ
At the standard 0.5 MPa operating pressure, the cylinder provides 3927 N pushing force and 3681 N pulling force. At the maximum operating pressure of 0.9 MPa, the push force increases to 7068 N. The theoretical maximum force at 1.0 MPa is 801 kgf.
To ensure a drop-in fit, confirm your current cylinder matches these five specifications: 100 mm bore, 760 mm stroke, PT1/2 port thread, a built-in magnet for sensors (-S), and a basic (no accessory) mounting style. This is an AirTAC SC tie-rod cylinder and will not directly interchange with ISO 15552 profile cylinders.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC100 Standard Cylinder SC100X760SN
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.