Airtac SC100 Standard Cylinder SC100X95TC
The AirTAC Airtac SC100 Standard Cylinder SC100X95TC is a genuine double-acting standard air cylinder with a Ø100mm bore and 95mm stroke, PT1/2 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ100 mm
- Stroke95 mm
- Port sizePT1/2
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 29 mm
About the Airtac SC100 Standard Cylinder SC100X95TC
The SC100X95TC is a double-acting pneumatic cylinder from the AirTAC SC tie-rod series, combining a 100 mm bore with a 95 mm stroke. At 0.5 MPa air pressure it generates a push force of 3927 N, making it a capable actuator for medium-duty pressing, clamping, and lifting tasks where a compact stroke is sufficient.
This model is factory-configured with a TC centre trunnion mount (supplied with the F-SC100TC bracket and TCM1 trunnion), allowing the cylinder body to pivot during operation. It uses a 25 mm diameter piston rod with an M20x1.5 male thread, PT1/2 ports, and an adjustable air cushion of 29 mm to decelerate the piston smoothly at each end of its 95 mm travel.
Airtac SC100 Standard Cylinder SC100X95TC Technical Specifications
| Model | Airtac SC100 Standard Cylinder SC100X95TC |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø100 mm |
| Stroke | 95 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (approx.) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC100 Standard Cylinder SC100X95TC
| SC | Standard tie-rod cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×95 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC100 Standard Cylinder SC100X95TC Is Used
Conveyor Diverter Gates
The 100 mm bore provides ample push force to reliably actuate heavy diverter gates or flippers on packaging and sortation conveyors, while the centre trunnion mount accommodates the arcing motion of the gate linkage.
Welding Fixture Clamping
Delivers 3927 N of clamping force at 0.5 MPa to hold steel fabrications securely in a welding jig. The 95 mm stroke offers a short, fast clamp/unclamp cycle, and the trunnion mount allows the cylinder to self-align as the clamp arm swings.
Agricultural Implement Tilt Control
Used to control the tilt angle of a plough or harrow section. The robust tie-rod construction withstands dusty, outdoor conditions, and the centre trunnion supports the pivoting motion required to adjust the implement's working angle.
Is the Airtac SC100 Standard Cylinder SC100X95TC the Right Cylinder?
Select the SC100X95TC when the application requires a 100 mm bore for its 3927 N push force at 0.5 MPa and a 95 mm stroke within a pivoting assembly. If the force requirement is lower, stepping down to an 80 mm bore (2513 N at 0.5 MPa) can reduce air consumption and physical size; for higher force demands, the 125 mm bore offers 6136 N at the same pressure. The centre trunnion mount is ideal for swinging loads, but ensure the pivot axis is aligned to avoid binding.
For a direct replacement, match all five key points: 100 mm bore, 95 mm stroke, PT1/2 port thread, TC centre trunnion mounting (F-SC100TC), and the standard TPU seal. This cylinder does not include a magnet; if you need barrel-mounted position sensors, order the -S variant (SC100X95STC).
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC100 Standard Cylinder SC100X95TC FAQ
At the standard 0.5 MPa operating pressure, the push force is 3927 N. At 0.7 MPa it rises to 5497 N, and at the maximum operating pressure of 0.9 MPa, the push force reaches 7068 N. The theoretical maximum force at 1.0 MPa is 801 kgf. All figures are for the outstroke; the pull force on the instroke is slightly lower due to the 25 mm rod area.
This specific model code (SC100X95TC) does not include the -S magnet option, so the piston does not carry a magnetic ring and standard reed or solid-state sensors (CMSG/DMSG/EMSG) cannot be used directly on the barrel. If you require position sensing, order the SC100X95STC variant which includes a built-in magnet, or use external limit switches actuated by the moving load.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC100 Standard Cylinder SC100X95TC
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.