Airtac SC80 Standard Cylinder SC80X1030
The AirTAC Airtac SC80 Standard Cylinder SC80X1030 is a genuine double-acting standard air cylinder with a Ø80mm bore and 1030mm stroke, PT3/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ80 mm
- Stroke1030 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 28 mm
About the Airtac SC80 Standard Cylinder SC80X1030
The AirTAC SC80X1030 is a double-acting tie-rod cylinder delivering a substantial 2513 N of push force at 0.5 MPa (4523 N at the 0.9 MPa maximum operating pressure). With an 80 mm bore and a 1030 mm stroke, this model is built for applications requiring a long, straight-line pneumatic thrust. The 25 mm diameter piston rod and 28 mm adjustable air cushion at each end ensure smooth deceleration even under high cycle rates.
This cylinder's total extended body length is approximately 1212 mm (182 mm body length A plus the 1030 mm stroke). The standard PT3/8 ports provide reliable air connections, and the TPU seals offer a wide operating temperature range from -20 to +70 °C. As a genuine AirTAC SC unit, it is a robust and cost-effective solution for industrial automation tasks demanding extended reach.
Airtac SC80 Standard Cylinder SC80X1030 Technical Specifications
| Model | Airtac SC80 Standard Cylinder SC80X1030 |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø80 mm |
| Stroke | 1030 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 28 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (approx.) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC80 Standard Cylinder SC80X1030
| SC | Standard tie-rod cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×1030 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC80 Standard Cylinder SC80X1030 Is Used
Long-Reach Material Transfer
Pushes or pulls heavy components across a wide conveyor gap, using the full 1030 mm stroke for part indexing or lane diverting in packaging lines.
Large Panel Pressing
Applies 2513 N of force at 0.5 MPa to laminate or press large wooden panels, furniture boards, or composite sheets, where the extended stroke clears the workpiece area for easy loading.
Automated Bin Tipping
Actuates a tipping mechanism for large bulk bins or pallets, using the long stroke to achieve the necessary dump angle with consistent force from the 80 mm bore cylinder.
Is the Airtac SC80 Standard Cylinder SC80X1030 the Right Cylinder?
Select the SC80X1030 when your application needs the 2513 N push force of an 80 mm bore over a long 1030 mm working distance. If a shorter stroke with the same force is acceptable, a standard-stroke model will reduce lead time. For higher force requirements, stepping up to the 100 mm bore (SC100 series) provides 3927 N at 0.5 MPa.
For this 1030 mm stroke, careful side-load management is critical. The long, unsupported 25 mm rod is susceptible to bending under lateral forces. Always ensure the load is guided externally on linear bearings or rails, and never use the piston rod as a guide. For a direct replacement, match the 80 mm bore, 1030 mm stroke, PT3/8 port thread, basic mounting, and the optional magnet if your existing unit has the -S suffix.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC80 Standard Cylinder SC80X1030 FAQ
At 0.7 MPa operating pressure, the SC80X1030 generates a push force of 3518 N and a pull force of 2268 N. The maximum push force at 0.9 MPa is 4523 N.
For a 1030 mm stroke, you must guide the load externally with linear bearings or a guide rail system. The cylinder should only provide push/pull force, not support side loads. For high side-load moments, consider an AirTAC guided cylinder series instead.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC80 Standard Cylinder SC80X1030
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.