Airtac SC80 Standard Cylinder SC80X10S
The AirTAC Airtac SC80 Standard Cylinder SC80X10S is a genuine double-acting standard air cylinder with a Ø80mm bore and 10mm stroke, PT3/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ80 mm
- Stroke10 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 28 mm
About the Airtac SC80 Standard Cylinder SC80X10S
The SC80X10S is an 80 mm bore double-acting tie-rod cylinder with a short 10 mm stroke, ideal for clamping, ejecting, or precise short-travel positioning. With a 25 mm diameter piston rod and PT3/8 ports, it generates a push force of 2513 N at 0.5 MPa and up to 4523 N at 0.9 MPa.
This model includes the factory-installed -S magnet, enabling direct mounting of CMSG, DMSG, or EMSG reed and solid-state sensors along the barrel for reliable end-of-stroke detection. The compact body length A of 182 mm plus the 10 mm stroke keeps the overall envelope tight for space-constrained automation cells.
Airtac SC80 Standard Cylinder SC80X10S Technical Specifications
| Model | Airtac SC80 Standard Cylinder SC80X10S |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø80 mm |
| Stroke | 10 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 28 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (approx.) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC80 Standard Cylinder SC80X10S
| SC | Standard tie-rod cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC80 Standard Cylinder SC80X10S Is Used
Short-Stroke Clamping
The 10 mm stroke and 2513 N force at 0.5 MPa make it perfect for pneumatic clamping fixtures where the jaw travel is minimal but holding power must be high.
Part Ejection
Delivers a quick, controlled 10 mm push to eject small parts from a die or mold, with the magnetic piston signaling the control system when the rod is fully retracted.
Diverter Gate Actuation
Operates a compact diverter gate on a conveyor line. The short stroke provides fast cycle times, while the built-in magnet confirms gate position for interlocking.
Is the Airtac SC80 Standard Cylinder SC80X10S the Right Cylinder?
For applications needing more force, the 100 mm bore SC100 series steps up to 3927 N at 0.5 MPa. If a shorter body is required, verify the minimum standard stroke of 25 mm. This cylinder is a direct replacement only for an AirTAC SC80 tie-rod unit matching the 80 mm bore, 10 mm stroke, PT3/8 ports, basic mount, and built-in magnet configuration.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC80 Standard Cylinder SC80X10S FAQ
At 0.7 MPa operating pressure, the theoretical push force is 3518 N. The pull force on the retract stroke is 2268 N at 0.5 MPa, accounting for the 25 mm rod area.
Yes. Even with a short 10 mm stroke, any side load should be carried by an external linear guide, not the rod bearing. The built-in magnet allows you to mount sensors without interfering with the guide structure.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC80 Standard Cylinder SC80X10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.