Airtac SC80 Standard Cylinder SC80X1350TC
The AirTAC Airtac SC80 Standard Cylinder SC80X1350TC is a genuine double-acting standard air cylinder with a Ø80mm bore and 1350mm stroke, PT3/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ80 mm
- Stroke1350 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 28 mm
About the Airtac SC80 Standard Cylinder SC80X1350TC
The AirTAC SC80X1350TC is a double-acting pneumatic cylinder delivering 2513 N of push force at 0.5 MPa and up to 4523 N at 0.9 MPa operating pressure. Its 1350 mm stroke remains within the 1500 mm maximum standard stroke for the 80 mm bore, making it a standard-length option for long-travel linear actuation.
This model features a 25 mm diameter piston rod with M20x1.5 threads and a 28 mm adjustable air cushion at each end for controlled deceleration. The TC suffix designates a centre trunnion mount, supplied with the TCM1 bracket (part code F-SC80TC), allowing the cylinder body to pivot and absorb side loads in swinging applications. The total extended body length is approximately 1532 mm.
Airtac SC80 Standard Cylinder SC80X1350TC Technical Specifications
| Model | Airtac SC80 Standard Cylinder SC80X1350TC |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø80 mm |
| Stroke | 1350 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 28 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (approx.) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC80 Standard Cylinder SC80X1350TC
| SC | Standard tie-rod cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×1350 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC80 Standard Cylinder SC80X1350TC Is Used
Long-Stroke Material Transfer
The 1350 mm stroke and 2513 N push force at 0.5 MPa efficiently shift heavy totes or pallets between distant conveyor lanes in packaging and logistics lines.
Pivoting Clamp & Weld Fixtures
The centre trunnion mount allows the cylinder to swing freely, making it ideal for actuating large pivoting clamps or welding jigs that require a long reach and high clamping force.
Grain Chute or Diverter Gate Actuation
Provides the long linear travel needed to fully open or close large diverter gates on chutes and hoppers in agricultural processing, with the trunnion mount accommodating the arc of motion.
Is the Airtac SC80 Standard Cylinder SC80X1350TC the Right Cylinder?
For applications requiring slightly less force, the 63 mm bore SC63 series provides 1559 N at 0.5 MPa. If higher force is needed, stepping up to the 100 mm bore SC100 series offers 3927 N at the same pressure. Always match replacement cylinders on all five critical points: bore, stroke, port thread (PT), mounting accessory (TC centre trunnion), and magnet option.
With a stroke of 1350 mm, the 25 mm rod is susceptible to bending under side loads. Do not use this cylinder to guide or support the load directly; install external linear guides or rod bearings to absorb any radial forces and prevent premature seal and bearing wear.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC80 Standard Cylinder SC80X1350TC FAQ
At the standard 0.5 MPa operating pressure, the push force is 2513 N and the pull force is 2268 N. At the maximum operating pressure of 0.9 MPa, the push force increases to 4523 N. The theoretical maximum force at 1.0 MPa is 513 kgf.
No. The AirTAC SC series is a tie-rod cylinder and is dimensionally shorter than an ISO 15552 profile cylinder, so it is not a direct drop-in replacement. It is a direct match only for another AirTAC SC tie-rod cylinder with an 80 mm bore, 1350 mm stroke, PT ports, and a centre trunnion (TC) mount.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC80 Standard Cylinder SC80X1350TC
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.