Airtac SC80 Standard Cylinder SC80X1410S
The AirTAC SC80 Standard Cylinder SC80X1410S is a genuine double-acting standard air cylinder with a Ø80mm bore and 1410mm stroke, PT3/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ80 mm
- Stroke1410 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 28 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SC80 Standard Cylinder SC80X1410S
The AirTAC SC80X1410S is a double-acting single-rod tie-rod cylinder with an 80 mm bore and a long 1410 mm stroke, factory-equipped with a built-in magnet for direct mounting of CMSG/DMSG/EMSG sensors. At 0.5 MPa it supplies 2513 N pushing force and 2268 N pulling force, rising to 4523 N push at the 0.9 MPa maximum operating pressure.
This model uses a 25 mm diameter piston rod with M20x1.5 male threads and PT3/8 ports. The adjustable air cushion (28 mm length) decelerates the piston near stroke end to reduce impact. The body length A is 182 mm, giving a total extended length of approximately 1592 mm. The standard TPU seals suit operating temperatures from -20 to +70 °C.
Airtac SC80 Standard Cylinder SC80X1410S Technical Specifications
| Model | Airtac SC80 Standard Cylinder SC80X1410S |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø80 mm |
| Stroke | 1410 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 28 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (approx.) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC80 Standard Cylinder SC80X1410S
| SC | Standard tie-rod cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×1410 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC80 Standard Cylinder SC80X1410S Is Used
Long-Reach Material Transfer
Moves parts or panels across wide conveyor gaps or between stations, using the 1410 mm stroke and sensor feedback for end-of-stroke confirmation.
Automated Gluing & Dispensing
Positions a dispensing head along a long linear axis; the built-in magnet allows CMSG/DMSG sensors to verify retract and extend positions precisely.
Pallet Staging & Stop Gates
Operates a long-travel stop gate or diverter arm in logistics lines, where the 2513 N push force at 0.5 MPa reliably holds and releases pallets.
Is the Airtac SC80 Standard Cylinder SC80X1410S the Right Cylinder?
Choose the SC80 bore when your application needs between roughly 2500 N and 4500 N of pneumatic force; step down to the SC63 (1559 N push at 0.5 MPa) for lighter loads or up to the SC100 (3927 N push at 0.5 MPa) for heavier ones. The 1410 mm stroke is within the 1500 mm maximum standard stroke for this bore.
At this stroke length, the extended 25 mm rod is susceptible to bending under side loads—always guide the load externally or use a guided cylinder if lateral forces are present. For a direct replacement, match bore (80 mm), stroke (1410 mm), PT3/8 port thread, the built-in magnet (-S), and the basic mounting configuration.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC80 Standard Cylinder SC80X1410S FAQ
At 0.5 MPa (approx. 73 psi) the cylinder pushes with 2513 N and pulls with 2268 N. At 0.7 MPa, push force rises to 3518 N, and at the 0.9 MPa maximum operating pressure it reaches 4523 N. The theoretical maximum at 1.0 MPa is 513 kgf.
Yes. The -S suffix indicates a built-in magnet, so AirTAC CMSG (reed) and DMSG/EMSG (solid-state) sensors clamp directly onto the barrel without additional brackets or magnet rings.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC80 Standard Cylinder SC80X1410S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.