Airtac SC80 Standard Cylinder SC80X2000SH
The AirTAC SC80 Standard Cylinder SC80X2000SH is a genuine double-acting standard air cylinder with a Ø80mm bore and 2000mm stroke, PT3/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ80 mm
- Stroke2000 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 28 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SC80 Standard Cylinder SC80X2000SH
The AirTAC SC80X2000SH is a double-acting tie-rod cylinder with an 80 mm bore and an extended 2000 mm non-standard stroke, built for applications demanding long linear travel. At 0.5 MPa it pushes with 2513 N, and at the maximum operating pressure of 0.9 MPa the thrust rises to 4523 N, driven by a 25 mm diameter piston rod.
This model carries the -S magnet suffix for direct mounting of CMSG/DMSG/EMSG sensors on the barrel, and the -H seal suffix upgrading the seals to Viton (FKM) for a 0 to +150 °C operating range. The total extended body length is approximately 2182 mm, with a 28 mm adjustable air cushion at each end to decelerate the piston smoothly.
Airtac SC80 Standard Cylinder SC80X2000SH Technical Specifications
| Model | Airtac SC80 Standard Cylinder SC80X2000SH |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø80 mm |
| Stroke | 2000 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 28 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (approx.) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC80 Standard Cylinder SC80X2000SH
| SC | Standard tie-rod cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×2000 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC80 Standard Cylinder SC80X2000SH Is Used
Long-Reach Material Pusher
The 2000 mm stroke and 4523 N push force at 0.9 MPa suit long-distance part ejection or pallet pushing in automated warehouses, where extended reach is essential.
High-Temperature Autoclave Actuation
Viton seals enable reliable operation in 0-150°C environments, making this cylinder suitable for actuating doors or racks inside autoclaves and sterilisation equipment.
Sensor-Monitored Long-Stroke Clamping
The built-in magnet allows CMSG/DMSG sensors to confirm full extension and retraction over the 2000 mm travel, ideal for automated clamping fixtures with extended reach.
Is the Airtac SC80 Standard Cylinder SC80X2000SH the Right Cylinder?
For applications needing slightly less force, the 63 mm bore SC63 series delivers 1559 N push at 0.5 MPa and can be a more compact alternative. If higher force is required, stepping up to the 100 mm bore provides 3927 N at the same pressure. At this 2000 mm stroke, the unsupported rod length is significant—side loads or off-centre mounting can cause rod bending and premature bearing wear. Always use an external linear guide or a guided cylinder configuration to absorb lateral forces and protect the rod bearing.
To replace an existing SC80X2000SH, match five points: 80 mm bore, 2000 mm stroke, PT port thread, built-in magnet (-S), and Viton seals (-H). The SC is a tie-rod design and is not dimensionally interchangeable with ISO 15552 profile cylinders.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC80 Standard Cylinder SC80X2000SH FAQ
At 0.5 MPa the push force is 2513 N and the pull force is 2268 N. At the maximum operating pressure of 0.9 MPa, the push force reaches 4523 N. The theoretical maximum at 1.0 MPa is 513 kgf.
No. The SC80X2000SH is a double-acting cylinder and does not lock or hold position when pressure is exhausted or the directional valve is centred. For load holding without live pressure, an external rod brake, mechanical lock, or pilot-operated check valve is required.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC80 Standard Cylinder SC80X2000SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.