Airtac SC80 Standard Cylinder SC80X223S
The AirTAC SC80 Standard Cylinder SC80X223S is a genuine double-acting standard air cylinder with a Ø80mm bore and 223mm stroke, PT3/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ80 mm
- Stroke223 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 28 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SC80 Standard Cylinder SC80X223S
The AirTAC SC80X223S is a double-acting tie-rod cylinder with an 80 mm bore and a 223 mm stroke, delivering a push force of 2513 N at 0.5 MPa and up to 4523 N at 0.9 MPa. The built-in magnet (suffix -S) allows CMSG/DMSG/EMSG reed or solid-state sensors to clamp directly onto the barrel for reliable end-of-stroke or mid-stroke position feedback.
This model uses a 25 mm diameter piston rod with an M20x1.5 male thread and PT3/8 ports. The adjustable air cushion (28 mm length) decelerates the piston smoothly at both ends, reducing impact noise and wear. With a body length A of 182 mm, the total extended length is approximately 405 mm, making it a compact choice for medium-force clamping, pressing, and transfer tasks.
Airtac SC80 Standard Cylinder SC80X223S Technical Specifications
| Model | Airtac SC80 Standard Cylinder SC80X223S |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø80 mm |
| Stroke | 223 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 28 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (approx.) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC80 Standard Cylinder SC80X223S
| SC | Standard tie-rod cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×223 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC80 Standard Cylinder SC80X223S Is Used
Package Diverting & Sorting
The 223 mm stroke and 2513 N push force reliably divert cartons and totes on belt conveyors. The built-in magnet enables sensor confirmation of each divert cycle.
Medium-Duty Clamping
Ideal for pneumatic clamping fixtures in machining or welding cells. The adjustable cushion protects the workpiece and fixture from impact at the end of the 223 mm stroke.
Waste Compaction
Generates up to 4523 N at 0.9 MPa to compact cardboard, plastic, or light metal scrap in small baling or compaction equipment.
Is the Airtac SC80 Standard Cylinder SC80X223S the Right Cylinder?
Choose the SC80 when your application needs roughly 2500 N of force at standard plant air pressure. If your load is lighter, the SC63 delivers 1559 N push at 0.5 MPa and may reduce air consumption; for heavier loads, the SC100 provides 3927 N at the same pressure. Always match the replacement cylinder on all five key points: bore, stroke, PT3/8 port thread, the built-in magnet (-S), and the basic (no bracket) mounting configuration.
At 223 mm stroke, the 25 mm rod is well supported inside the standard bore, but any significant side load still demands an external guide rail or a guided cylinder to protect the rod bearing and seals from premature wear and bending.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC80 Standard Cylinder SC80X223S FAQ
At 0.5 MPa, the push force is 2513 N and the pull force is 2268 N. At the maximum operating pressure of 0.9 MPa, push force reaches 4523 N. The theoretical maximum force at 1.0 MPa is 513 kgf.
No. The SC series is a tie-rod cylinder that is shorter than an ISO 15552 cylinder, so it is not dimensionally interchangeable. Only replace another AirTAC SC tie-rod cylinder with the same bore, stroke, PT3/8 ports, and built-in magnet.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC80 Standard Cylinder SC80X223S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.