Airtac SC80 Standard Cylinder SC80X530
The AirTAC SC80 Standard Cylinder SC80X530 is a genuine double-acting standard air cylinder with a Ø80mm bore and 530mm stroke, PT3/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ80 mm
- Stroke530 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 28 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SC80 Standard Cylinder SC80X530
The AirTAC SC80X530 is a double-acting pneumatic cylinder delivering a substantial 2513 N of push force at 0.5 MPa, scaling up to 4523 N at the maximum operating pressure of 0.9 MPa. With an 80 mm bore and a 25 mm diameter piston rod, this tie-rod cylinder is built for industrial tasks requiring a robust mid-range force over a non-standard stroke length of 530 mm.
This model features a 28 mm adjustable air cushion at each end to decelerate the piston smoothly, reducing impact and noise. The body length is 182 mm, resulting in a total extended length of approximately 712 mm. It uses PT3/8 ports and an M20x1.5 rod thread, and is configured here with the default TPU seals for a standard operating temperature range of -20 to +70 °C.
Airtac SC80 Standard Cylinder SC80X530 Technical Specifications
| Model | Airtac SC80 Standard Cylinder SC80X530 |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø80 mm |
| Stroke | 530 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 28 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (approx.) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC80 Standard Cylinder SC80X530
| SC | Standard tie-rod cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×530 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC80 Standard Cylinder SC80X530 Is Used
Material Transfer Systems
Pushes or diverts heavy boxes and totes on wide conveyor lines. The 2513 N force at 0.5 MPa handles substantial product weights, while the 530 mm stroke bridges large gaps between conveyors.
Press-Fit Assembly
Provides the controlled, high-force push needed to press bearings, bushings, or pins into place. The adjustable cushion ensures a clean stop without jarring the assembly fixture at the end of the 530 mm stroke.
Waste Compaction Equipment
Drives a compaction plate to crush and consolidate recyclable materials or waste. The cylinder's 4523 N maximum thrust at 0.9 MPa delivers the necessary compaction force for dense bales.
Is the Airtac SC80 Standard Cylinder SC80X530 the Right Cylinder?
For applications needing slightly less force, the 63 mm bore SC63 series provides 1559 N of push at 0.5 MPa. If your load requires more power, stepping up to the 100 mm bore SC100 series offers 3927 N at the same pressure. Always match the bore to the required force at your available air pressure, leaving a safety margin.
This 530 mm stroke is a non-standard, made-to-order length for the 80 mm bore. For any stroke over 300 mm, particularly with a 25 mm rod, carefully assess side loads. An unsupported long stroke is vulnerable to rod bending and bearing wear; use an external linear guide or a guided cylinder to absorb transverse forces. When replacing an existing cylinder, verify five key points: 80 mm bore, 530 mm stroke, PT3/8 port thread, basic mounting (no integral bracket), and the absence of a built-in magnet.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC80 Standard Cylinder SC80X530 FAQ
At the standard 0.5 MPa operating pressure, the push force is 2513 N and the pull force is 2268 N. At the maximum operating pressure of 0.9 MPa, the push force increases to 4523 N. The theoretical maximum force at 1.0 MPa is 513 kgf.
The 530 mm stroke is a non-standard length for the 80 mm bore, so it is a made-to-order item. For a direct physical replacement, you must match an AirTAC SC80 tie-rod cylinder with the exact 530 mm stroke, PT3/8 ports, basic mounting, and no magnet. An ISO 15552 cylinder will not fit as a direct substitute due to different body dimensions.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC80 Standard Cylinder SC80X530
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.