Airtac SC80 Standard Cylinder SC80X530S
The AirTAC SC80 Standard Cylinder SC80X530S is a genuine double-acting standard air cylinder with a Ø80mm bore and 530mm stroke, PT3/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ80 mm
- Stroke530 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 28 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SC80 Standard Cylinder SC80X530S
The SC80X530S is a double-acting pneumatic cylinder with an 80 mm bore and a non-standard 530 mm stroke, built with a built-in magnet (suffix -S) for direct mounting of CMSG/DMSG/EMSG reed or solid-state sensors. At 0.5 MPa air pressure it delivers 2513 N pushing force and 2268 N pulling force, rising to a maximum theoretical thrust of 4523 N at 0.9 MPa.
This model uses a 25 mm diameter piston rod with an M20x1.5 male thread and PT3/8 port connections. The body length A is 182 mm, giving an approximate extended length of 712 mm. Its adjustable pneumatic cushion (28 mm length) decelerates the piston at stroke ends, and the standard TPU seals suit operating temperatures from -20 to +70 °C.
Airtac SC80 Standard Cylinder SC80X530S Technical Specifications
| Model | Airtac SC80 Standard Cylinder SC80X530S |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø80 mm |
| Stroke | 530 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 28 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (approx.) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC80 Standard Cylinder SC80X530S
| SC | Standard tie-rod cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×530 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC80 Standard Cylinder SC80X530S Is Used
Long-Stroke Part Transfer
The 530 mm stroke and 2513 N push force reliably shift heavy components between distant conveyor stations, with the built-in magnet enabling end-of-stroke position confirmation.
Automated Clamping & Fixturing
Delivers consistent clamping force for large weldments or assemblies. The adjustable cushion prevents impact shock, protecting the fixture and part alignment over millions of cycles.
Pallet Dispensing Systems
Pushes or pulls heavy pallets in automated storage and retrieval systems. The non-standard 530 mm stroke provides the extended reach needed for deep magazine lanes.
Is the Airtac SC80 Standard Cylinder SC80X530S the Right Cylinder?
Choose the SC80X530S when your application needs the 2513 N push force of an 80 mm bore at 0.5 MPa but requires a stroke beyond the standard 500 mm range. If your force requirement is lower, stepping down to a 63 mm bore (1559 N at 0.5 MPa) can reduce air consumption and physical size. For higher forces, the 100 mm bore delivers 3927 N at 0.5 MPa.
At 530 mm stroke, the unsupported rod length increases the risk of bending under side loads. Always guide the load externally with linear rails or rods, or consider a guided cylinder assembly, to protect the rod bearing and piston seals. For direct replacement, match bore (80 mm), stroke (530 mm), port thread (PT3/8), the built-in magnet (-S), and the basic mounting configuration.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC80 Standard Cylinder SC80X530S FAQ
At 0.5 MPa (5 bar), the cylinder provides 2513 N pushing force and 2268 N pulling force. At the maximum operating pressure of 0.9 MPa, the pushing force reaches 4523 N. The theoretical maximum force at 1.0 MPa is 513 kgf.
No. For any stroke of 300 mm or more, especially with a non-standard 530 mm stroke, side loads can bend the 25 mm rod and damage the bearing. An external guide system or a guided cylinder is required to absorb transverse forces and ensure long service life.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC80 Standard Cylinder SC80X530S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.