Airtac SC80 Standard Cylinder SC80X710S
The AirTAC Airtac SC80 Standard Cylinder SC80X710S is a genuine double-acting standard air cylinder with a Ø80mm bore and 710mm stroke, PT3/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ80 mm
- Stroke710 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 28 mm
About the Airtac SC80 Standard Cylinder SC80X710S
The AirTAC SC80X710S is a double-acting tie-rod cylinder with an 80 mm bore and a 710 mm stroke, factory-equipped with a built-in magnet for barrel-mounted position sensors. At 0.5 MPa it generates 2513 N pushing force, rising to 4523 N at the 0.9 MPa maximum operating pressure, making it a solid mid-range actuator for moderate transfer and clamping tasks.
This model uses a 25 mm diameter piston rod with M20x1.5 male threads and PT3/8 ports. The adjustable air cushion (28 mm length) decelerates the piston smoothly at each end. With a body length A of 182 mm, total extended length is approximately 892 mm. The -S suffix adds a magnet band, allowing CMSG/DMSG/EMSG sensors to clamp directly onto the barrel for reliable end-of-stroke or mid-stroke sensing.
Airtac SC80 Standard Cylinder SC80X710S Technical Specifications
| Model | Airtac SC80 Standard Cylinder SC80X710S |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø80 mm |
| Stroke | 710 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 28 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (approx.) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC80 Standard Cylinder SC80X710S
| SC | Standard tie-rod cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×710 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC80 Standard Cylinder SC80X710S Is Used
Long-Reach Part Transfer
The 710 mm stroke moves parts between distant conveyor stations or into a multi-level assembly fixture, with sensor magnets confirming arrival at each end.
Clamping & Holding in Woodworking
Delivers over 2.5 kN at 0.5 MPa to hold panels or jigs during routing and drilling, while the magnet sensors interlock with machine safety circuits.
Palletising Pusher
Pushes boxes or trays across a roller table onto a pallet. The adjustable cushion prevents hard stops that could shift the load at the end of the 710 mm travel.
Is the Airtac SC80 Standard Cylinder SC80X710S the Right Cylinder?
Choose the SC80X710S when your application needs roughly 2500 N at standard shop air and a stroke near 700 mm. If the load is lighter and you can accept a smaller footprint, stepping down to the 63 mm bore (1559 N at 0.5 MPa) saves space and air consumption. For higher force, the 100 mm bore delivers 3927 N at the same pressure.
At 710 mm stroke, the 25 mm rod is long enough that side loads or off-centre mounting can cause rod bending and premature bearing wear. Always align the load axially or add an external guide rail to absorb transverse forces. For direct replacement, match five points: 80 mm bore, 710 mm stroke, PT3/8 ports, the built-in magnet (-S suffix), and the basic mounting style (no bracket).
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC80 Standard Cylinder SC80X710S FAQ
At 0.5 MPa the cylinder pushes with 2513 N and pulls with 2268 N. At the maximum operating pressure of 0.9 MPa, pushing force reaches 4523 N. The theoretical maximum at 1.0 MPa is 513 kgf.
Yes. The -S suffix indicates a built-in magnet around the piston, so AirTAC CMSG (reed) or DMSG/EMSG (solid-state) sensors clamp directly onto the barrel to detect piston position without external brackets or flags.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC80 Standard Cylinder SC80X710S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.