Airtac SC80 Standard Cylinder SC80X715S
The AirTAC Airtac SC80 Standard Cylinder SC80X715S is a genuine double-acting standard air cylinder with a Ø80mm bore and 715mm stroke, PT3/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ80 mm
- Stroke715 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 28 mm
About the Airtac SC80 Standard Cylinder SC80X715S
The SC80X715S is a double-acting pneumatic cylinder delivering 2513 N of push force at 0.5 MPa, scaling up to 4523 N at the maximum operating pressure of 0.9 MPa. With an 80 mm bore and a 715 mm stroke, its 25 mm diameter piston rod and 28 mm adjustable air cushion provide reliable deceleration for mid-to-long stroke linear tasks.
This model includes a built-in magnet (-S suffix), allowing direct mounting of CMSG, DMSG, or EMSG reed and solid-state sensors on the barrel for non-contact position sensing. The cylinder uses a PT3/8 port, standard TPU seals for a -20 to +70 °C range, and a body length of 182 mm, resulting in a total extended length of approximately 897 mm.
Airtac SC80 Standard Cylinder SC80X715S Technical Specifications
| Model | Airtac SC80 Standard Cylinder SC80X715S |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø80 mm |
| Stroke | 715 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 28 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (approx.) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC80 Standard Cylinder SC80X715S
| SC | Standard tie-rod cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×715 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC80 Standard Cylinder SC80X715S Is Used
Material Transfer
Pushes or diverts boxes and totes on packaging lines, where the 2513 N force at 0.5 MPa handles medium-weight loads and the magnet enables end-of-stroke confirmation.
Clamping & Fixturing
Provides consistent clamping pressure for woodworking or metal fabrication jigs, using the adjustable cushion to soften the impact at full extension.
Bin Tipping & Hopper Gates
Operates discharge gates on bulk bins, with the sensor-ready magnet confirming the gate is fully open or closed in automated processing lines.
Is the Airtac SC80 Standard Cylinder SC80X715S the Right Cylinder?
Select the SC80 when the SC63’s 1559 N force at 0.5 MPa is insufficient; if more force is needed, the SC100 provides 3927 N at the same pressure. For this 715 mm stroke, side loads must be managed carefully—an unsupported rod of this length can experience bending under lateral force, so consider an external linear guide or a guided cylinder if the load is not purely axial. To ensure a direct replacement, match the 80 mm bore, 715 mm stroke, PT3/8 port thread, built-in magnet (-S), and basic mounting configuration.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC80 Standard Cylinder SC80X715S FAQ
At 0.5 MPa, the cylinder provides 2513 N pushing and 2268 N pulling. At the maximum operating pressure of 0.9 MPa, the push force increases to 4523 N. The theoretical maximum force at 1.0 MPa is 513 kgf.
Match the 80 mm bore, 715 mm stroke, PT3/8 port thread, and the built-in magnet for sensor compatibility. This is a tie-rod cylinder, not an ISO 15552 profile, so verify the shorter body length (182 mm) and mounting hole pattern against your current unit.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC80 Standard Cylinder SC80X715S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.