Airtac SC80 Standard Cylinder SC80X750
The AirTAC Airtac SC80 Standard Cylinder SC80X750 is a genuine double-acting standard air cylinder with a Ø80mm bore and 750mm stroke, PT3/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ80 mm
- Stroke750 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 28 mm
About the Airtac SC80 Standard Cylinder SC80X750
The AirTAC SC80X750 is a double-acting pneumatic cylinder delivering 2513 N of push force at 0.5 MPa and up to 4523 N at 0.9 MPa. With an 80 mm bore and a 750 mm stroke, this tie-rod cylinder is built for applications needing a robust mid-range linear actuator.
Its 25 mm diameter piston rod and 28 mm adjustable air cushion provide reliable end-of-stroke deceleration. The total extended body length is approximately 932 mm (182 mm body length A + 750 mm stroke). PT3/8 ports and an M20x1.5 rod thread are standard.
Airtac SC80 Standard Cylinder SC80X750 Technical Specifications
| Model | Airtac SC80 Standard Cylinder SC80X750 |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø80 mm |
| Stroke | 750 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 28 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (approx.) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC80 Standard Cylinder SC80X750
| SC | Standard tie-rod cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×750 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC80 Standard Cylinder SC80X750 Is Used
Material Transfer
Pushes or diverts medium-weight packages on conveyor lines with a 750 mm reach, operating reliably in dusty or humid conditions with TPU seals.
Press-Fit Assembly
Applies up to 4523 N of force at 0.9 MPa for pressing bearings or bushings into housings, with adjustable cushioning to protect the workpiece.
Farm Implement Actuation
Controls chute gates or bin doors on agricultural equipment, providing a long 750 mm stroke for wide-opening mechanisms.
Is the Airtac SC80 Standard Cylinder SC80X750 the Right Cylinder?
Choose the SC80X750 when your application requires around 2500 N of force. If you need more force, step up to the SC100 bore (3927 N at 0.5 MPa); for less, the SC63 provides 1559 N. At a 750 mm stroke, ensure the rod is guided externally if significant side loads are present to prevent bending and premature bearing wear. For replacement, match bore, stroke, PT3/8 ports, and the basic mounting configuration.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC80 Standard Cylinder SC80X750 FAQ
At 0.5 MPa air pressure, the push force is 2513 N and the pull force is 2268 N. At the maximum operating pressure of 0.9 MPa, the push force increases to 4523 N.
For strokes over 300 mm, side loading on the 25 mm rod can cause bending. It is recommended to use an external guide rail or rod support to ensure long seal and bearing life, especially under heavy or off-center loads.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC80 Standard Cylinder SC80X750
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.