Airtac SC80 Standard Cylinder SC80X880S
The AirTAC Airtac SC80 Standard Cylinder SC80X880S is a genuine double-acting standard air cylinder with a Ø80mm bore and 880mm stroke, PT3/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ80 mm
- Stroke880 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 28 mm
About the Airtac SC80 Standard Cylinder SC80X880S
The SC80X880S is an AirTAC tie-rod cylinder with an 80 mm bore and an 880 mm stroke, factory-equipped with a built-in magnet for barrel-mounted sensors. It generates 2513 N of push force at 0.5 MPa and climbs to 4523 N at the maximum operating pressure of 0.9 MPa, placing it in a force class ideal for medium-duty pressing and clamping.
This model uses a 25 mm diameter piston rod and PT3/8 ports. The body length A is 182 mm, giving an extended length of approximately 1062 mm. Its 28 mm adjustable air cushion decelerates the end-of-stroke load, and the -S suffix enables direct mounting of CMSG, DMSG, or EMSG reed and solid-state sensors for reliable position feedback.
Airtac SC80 Standard Cylinder SC80X880S Technical Specifications
| Model | Airtac SC80 Standard Cylinder SC80X880S |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø80 mm |
| Stroke | 880 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 28 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (approx.) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC80 Standard Cylinder SC80X880S
| SC | Standard tie-rod cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×880 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC80 Standard Cylinder SC80X880S Is Used
Conveyor Diverter Gates
The 880 mm stroke and 2513 N push force at 0.5 MPa reliably actuate long-throw diverter gates on packaging and sortation lines, with the built-in magnet confirming gate position via barrel sensors.
Automated Gluing & Dispensing
Provides the extended reach needed for adhesive applicator heads moving across large panels. The -S magnet allows precise mid-stroke or end-stroke sensing to trigger the dispense cycle.
Pallet Layer Forming
Delivers consistent force to push stacked layers of product onto a pallet. The 28 mm adjustable cushion decelerates the heavy mass smoothly, protecting the palletizing cell structure.
Is the Airtac SC80 Standard Cylinder SC80X880S the Right Cylinder?
Choose the SC80 bore when the 50 mm bore’s 982 N push at 0.5 MPa is insufficient; stepping up to 80 mm nearly triples the available force. If your application demands even higher thrust, the SC100 bore provides 3927 N at the same pressure. For this 880 mm stroke, ensure the rod is protected from side loads—external guides or a self-guided unit should be used to prevent rod bending and premature bearing wear.
To replace an existing cylinder, match five points: 80 mm bore, 880 mm stroke, PT3/8 port thread, the built-in magnet (-S), and the basic mounting configuration. This SC model is a tie-rod design and is not dimensionally interchangeable with ISO 15552 profile cylinders.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC80 Standard Cylinder SC80X880S FAQ
At 0.7 MPa operating pressure, the push force is 3518 N. The maximum push force at 0.9 MPa is 4523 N. These values assume a standard double-acting configuration with filtered air.
Yes. The -S suffix in SC80X880S indicates a built-in magnet inside the piston. This allows AirTAC CMSG, DMSG, or EMSG sensors to be clamped directly onto the tie-rod barrel for non-contact position detection without additional brackets.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC80 Standard Cylinder SC80X880S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.