
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X100-20 is a genuine double-acting COMPACT cylinder (Ø63mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 80 to 100 mm on the machine — no shims, no part change.
The AirTAC SDAJ63X100-20 is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. By turning the R (M16x1.5) screw, you can dial the forward stroke down from the 100 mm maximum to 80 mm directly on the machine, eliminating the need for shims or part swaps during changeovers. Retract remains full length. This on-site tuning capability drastically reduces commissioning time for trial positioning.
The short riveted body saves valuable axial mounting depth where a larger profile cylinder will not fit. End shock is managed solely by a fixed NBR bumper, which decelerates the stroke end but is not an adjustable air cushion. Note that this specific SKU lacks a piston magnet and therefore cannot support reed or electronic switches.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X100-20 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Max stroke | 100 mm |
| Adjustable range | 80 – 100 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | — |
| Max (@1.0 MPa) | 286 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×100 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Allows operators to fine-tune the 80-100 mm extend stop on the machine floor, achieving exact insertion depth for bearing presses without swapping physical spacers.
Stepping down to the SDAJ50 yields 981.7 N, which may be insufficient for heavier payloads, while stepping up to the SDAJ80 provides 2513.3 N for high-mass transfers.
This model is specified with a 100 mm maximum stroke, a 20 mm adjust window, a PT1/4 port, a female rod-end thread (M10x1.5), and no magnet (S). It is perfect for setups requiring frequent on-site stroke tuning. Remember that a plain cylinder does not hold its load on air loss or valve centring; the piston drifts and the fixed bumper only decelerates near the end. For secure load holding without live pressure, integrate an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ63 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj63-adjustable-cylinder
Quick checklist
The theoretical maximum push is 318 kgf at 1.0 MPa.
The R (M16x1.5) screw mechanically shortens the extend stop between 80 and 100 mm without changing the output force. It is a mechanical stop, not a mid-stroke lock; the cylinder cannot hold a load on air loss and requires an external rod lock for holding.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.