
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X50-30 is a genuine double-acting COMPACT cylinder (Ø63mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 20 to 50 mm on the machine — no shims, no part change.
The AirTAC SDAJ63X50-30 is a double-acting compact cylinder featuring an external M16x1.5 adjuster screw that lets you dial the extend stop anywhere between 20 and 50 mm directly on the machine. The short riveted body drastically reduces axial mounting depth, fitting easily where standard round-body or profile cylinders cannot.
End-of-travel deceleration relies on a fixed NBR bumper rather than an adjustable air cushion, absorbing shock without needing tuning. Operating speed spans 30-500 mm/s, and the PT1/4 port feeds a 20 mm piston rod. Note that this specific SKU lacks a piston magnet, so it cannot host reed or electronic switches without upgrading to the -S variant.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X50-30 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Max stroke | 50 mm |
| Adjustable range | 20 – 50 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | — |
| Max (@1.0 MPa) | 286 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×50 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 20 to 50 mm to secure varying raw casting widths on a milling fixture without machining custom spacer plates.
Set precise downward travel limits for layer placement, using the fixed NBR bumper to absorb the impact of repetitive end-of-stroke contact.
This model suits fixtures requiring frequent changeover or trial positioning, as the M16x1.5 screw shortens the extend stroke by up to 30 mm without part swaps.
Remember that the fixed NBR bumper only decelerates the stroke end; it does not function as a lock. If your application must hold a load during air loss or valve centering, install an external rod lock or a pilot-operated check valve. Confirm your bore, 50 mm maximum stroke, 30 mm window, PT1/4 port, female M10x1.5 rod thread, and lack of a magnet (no -S) before ordering.
AirtacDistr lists every SDAJ63 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj63-adjustable-cylinder
Quick checklist
The theoretical maximum push is 318 kgf at 1.0 MPa. Operating pressure ranges from 0.15 to 1.0 MPa, with a speed of 30-500 mm/s.
Turning the external M16x1.5 screw mechanically shortens the extend stop from the 50 mm maximum down to 20 mm. It sets the end-stop boundary and does not alter force or lock the piston mid-stroke. This SKU lacks a magnet, so position sensing requires the -S variant.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.