
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X60-30 is a genuine double-acting COMPACT cylinder (Ø63mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 30 to 60 mm on the machine — no shims, no part change.
The AirTAC SDAJ63X60-30 is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. A built-in M16x1.5 adjuster screw lets you dial the outward stroke anywhere between 30 and 60 mm directly at the machine, eliminating the need for shims or part swaps during changeovers.
Its short riveted body significantly reduces axial mounting depth, fitting easily into tight spaces where larger profile cylinders cannot. The unit relies on a fixed NBR bumper at each end to decelerate the stroke, which is not an adjustable air cushion or a locking brake. Operating pressure spans 0.15 to 1.0 MPa across a 30 to 500 mm/s speed range, and this specific SKU lacks a piston magnet, meaning it cannot support reed or electronic switches without upgrading to the -S variant.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X60-30 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Max stroke | 60 mm |
| Adjustable range | 30 – 60 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | — |
| Max (@1.0 MPa) | 286 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×60 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial in the 30-60 mm extend stop during tooling changeovers to securely clamp raw castings without swapping out the entire actuator body.
Choose this model if your fixture requires frequent on-machine stroke tuning within the 30 to 60 mm window.
Confirm the bore, 60 mm maximum stroke, 30 mm adjustment window, and PT1/4 air port match your pneumatic supply. This SKU has no magnet (no -S code) and uses a female M10x1.5 rod-end thread on its 20 mm rod. Remember that a plain cylinder does not hold its load if air pressure drops or the valve centers—the piston will drift, as the fixed bumper only decelerates near the end of travel. For suspended or vertical loads, integrate an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ63 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj63-adjustable-cylinder
Quick checklist
At 0.7 MPa, push increases to 2182.1 N and pull to 1962.2 N. The theoretical maximum push is 318 kgf at 1.0 MPa.
Turning the external M16x1.5 screw shortens the extend stroke by up to 30 mm, allowing the outward endpoint to be set anywhere between 30 and 60 mm. The retract stroke remains full, and the screw acts only as a mechanical stop, not a mid-stroke lock.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.