
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X85-10B is a genuine double-acting COMPACT cylinder (Ø63mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 75 to 85 mm on the machine — no shims, no part change.
The AirTAC SDAJ63X85-10B is a double-acting compact cylinder featuring an external R (M16x1.5) adjustment screw that dials the extend stop directly on your machine. You can tune the outward stroke anywhere between 75 and 85 mm without swapping shims or parts, while the retract motion remains full length.
This variant uses a male-threaded piston rod (M18x1.5) for direct mounting and operates at speeds from 30 to 500 mm/s. The short riveted body significantly saves axial mounting depth where a larger profile cylinder will not fit. End-of-travel deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion or a mid-stroke lock.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X85-10B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Max stroke | 85 mm |
| Adjustable range | 75 – 85 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 10 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | — |
| Max (@1.0 MPa) | 286 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×85 | Maximum stroke length in mm. |
| -10 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial in the 75-85 mm extend stop during initial commissioning to perfectly seat parts without re-machining hard stops.
Quickly adjust the male M18x1.5 rod endpoint by up to 10 mm when switching between product variants on a shared line.
When sizing this 63 mm bore, evaluate both neighbouring options. This SDAJ63X85-10B bridges that gap with a theoretical maximum of 318 kgf at 1.0 MPa.
Choose this specific configuration when your fixture requires precise on-site extend tuning within the 75-85 mm window. Confirm your setup needs the male M18x1.5 rod thread and the PT1/4 air port. Note that this SKU lacks a piston magnet, so it cannot accept reed or electronic switches unless you specify the -S option. Finally, a plain pneumatic actuator does not hold a load if air pressure drops or the valve centres; the bumper only decelerates near the end. For secure load holding without live pressure, install an external rod lock or a pilot-operated check valve.
Quick checklist
At 0.7 MPa, push increases to 2182.1 N. The theoretical maximum push is 318 kgf at 1.0 MPa.
Turning the M16x1.5 R screw shortens the extend endpoint from the 85 mm maximum down to 75 mm. This sets a mechanical stop and does not alter the force. It is not a lock; the cylinder will drift if air is lost, so use an external rod lock for load holding.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.