
The AirTAC SDAJ80~100 Adjustable Super Slim Cylinder SDAJ80X60-40B is a genuine double-acting COMPACT cylinder (Ø80mm bore) whose extend end-position is set by an external M20×1.5 adjustment screw. You can dial the stroke anywhere from 20 to 60 mm on the machine — no shims, no part change.
The AirTAC SDAJ80X60-40B is a double-acting compact cylinder featuring an external extend stop. By turning the R (M20x1.5) adjuster screw, you can dial the forward stroke down by up to 40 mm, yielding a usable extension range of 20 to 60 mm directly on the machine. This on-site tuning eliminates the need for shims or part swaps during commissioning.
This specific SKU includes a male-threaded piston rod (M22x1.5) for secure external mounting and operates via a PT3/8 port. Built with a short riveted body, it saves axial mounting depth where a longer cylinder would fail to fit. End-of-travel deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. Note that this base configuration lacks a piston magnet, so it cannot support reed or electronic switches without upgrading to the -S variant.
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ80X60-40B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Max stroke | 60 mm |
| Adjustable range | 20 – 60 mm |
| Adjuster thread (R) | M20×1.5 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M14×1.5 F / M22×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 40 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2268 N | 2268 N |
| 0.7 MPa | 3175 N | — |
| Max (@1.0 MPa) | 463 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×60 | Maximum stroke length in mm. |
| -40 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Accommodate varying package lengths on a packaging line by tuning the extend stop on the fly, using the compact riveted body to fit tight transfer stations.
Control descent in lifting rigs where a 128.1 kg load is raised; set the mechanical stop precisely while relying on external check valves for load holding.
When sizing this model, evaluate your force requirements against neighbouring bores. Choose this 80 mm bore if your changeover routines demand precise, on-site stroke tuning between 20 and 60 mm.
Confirm your parameters before ordering: an 80 mm bore, 60 mm maximum stroke, 40 mm adjustment window, and a PT3/8 air supply. This unit features the -B male M22x1.5 rod end and no magnet. Because a plain double-acting cylinder drifts when air is lost or the valve is centered, the fixed NBR bumper only decelerates the stroke end and does not act as a lock. For suspended or vertical loads that must be held without live pressure, integrate an external rod lock or a pilot-operated check valve.
Quick checklist
At 0.7 MPa, push increases to 3518.6 N and pull to 3175 N. The theoretical maximum push is 513 kgf at 1.0 MPa.
Turning the external R (M20x1.5) screw shortens the forward stroke by up to 40 mm, allowing an extend range of 20 to 60 mm. The screw is strictly a mechanical stop, not a mid-stroke lock, and the cylinder will drift if air pressure is lost.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.