
The AirTAC SDAJ80~100 Adjustable Super Slim Cylinder SDAJ80X65-30S is a genuine double-acting COMPACT cylinder (Ø80mm bore) whose extend end-position is set by an external M20×1.5 adjustment screw. You can dial the stroke anywhere from 35 to 65 mm on the machine — no shims, no part change.
The AirTAC SDAJ80X65-30S is a compact double-acting double-rod cylinder engineered for on-site extend positioning. An external M20x1.5 adjuster screw lets you dial the outward stop anywhere between 35 and 65 mm without swapping shims or components, while retract remains full length. The short riveted body conserves axial mounting depth in tight machine envelopes where larger profile or round-body units fail to fit.
The built-in magnet (-S) supports AirTAC reed or electronic solid-state switches mounted directly into the body grooves. End-of-travel deceleration relies on a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion.
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ80X65-30S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Max stroke | 65 mm |
| Adjustable range | 35 – 65 mm |
| Adjuster thread (R) | M20×1.5 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M14×1.5 F / M22×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2268 N | 2268 N |
| 0.7 MPa | 3175 N | — |
| Max (@1.0 MPa) | 463 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×65 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 35 to 65 mm to set precise contact depth for pressing bearings, avoiding part damage during initial fixture setup.
Adjust the outward reach on the fly to accommodate varying box heights, ensuring the 25 mm rod meets the panel at the correct angle without retooling.
When sizing this 80 mm bore unit, evaluate your force requirements both ways.
Opt for this specific model if your fixture demands exact outward reach tuning during commissioning or frequent product changeovers. Confirm your parameters: 80 mm bore, 65 mm max stroke, 30 mm adjust window, PT3/8 air port, female M14x1.5 rod thread, and the -S magnet for sensing. Remember that a standard compact cylinder drifts when air is removed or the valve centers; the fixed bumper only decelerates near the end. For secure load holding without live pressure, install an external rod lock or pilot-operated check valve.
Quick checklist
At 0.7 MPa push increases to 3518.6 N and pull to 3175 N. The theoretical maximum push is 513 kgf at 1.0 MPa.
The M20x1.5 screw shortens the extend end position by up to 30 mm, yielding a usable 35 to 65 mm outward stroke while retract stays full. The built-in magnet works with AirTAC reed or electronic solid-state switches for position sensing.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.