
The AirTAC SDAJ80~100 Adjustable Super Slim Cylinder SDAJ80X80-30S is a genuine double-acting COMPACT cylinder (Ø80mm bore) whose extend end-position is set by an external M20×1.5 adjustment screw. You can dial the stroke anywhere from 50 to 80 mm on the machine — no shims, no part change.
The AirTAC SDAJ80X80-30S is a compact double-acting double-rod cylinder engineered for on-site extend-stop tuning. An external M20x1.5 adjuster screw lets you dial the outward stroke anywhere between 50 and 80 mm, eliminating the need for shims or part swaps during machine commissioning.
Its short riveted body saves valuable axial mounting depth where larger profile or round-body units will not fit. The unit features a fixed NBR bumper at each end to decelerate the stroke end, operating effectively across a 30-500 mm/s speed range. Equipped with a built-in piston magnet, this variant directly supports AirTAC reed or electronic solid-state switches for precise end-of-travel detection.
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ80X80-30S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Max stroke | 80 mm |
| Adjustable range | 50 – 80 mm |
| Adjuster thread (R) | M20×1.5 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M14×1.5 F / M22×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2268 N | 2268 N |
| 0.7 MPa | 3175 N | — |
| Max (@1.0 MPa) | 463 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×80 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Adjust the outward stroke on the fly to accommodate varying package widths on a sorting line, relying on the fixed NBR bumper to absorb the end shock.
Stepping down to the SDAJ63 yields 1558.6 N, whereas the SDAJ100 provides 3927 N, making this 80 mm bore the optimal middle ground for medium-heavy actuation. It is specifically recommended for setup-heavy lines requiring frequent changeover or trial positioning, allowing operators to set the exact extend endpoint without disassembling the actuator.
Confirm your parameters: an 80 mm bore, 80 mm maximum stroke, 30 mm adjustment window, and a PT3/8 air port. This configuration includes the -S magnet for switch sensing and a female M14x1.5 rod-end thread. Remember that a plain cylinder does not hold its load on air loss or when the valve is centred; the piston drifts and the fixed bumper only decelerates near the stroke end. For secure load holding without live pressure, integrate an external rod lock or a pilot-operated check valve.
Quick checklist
The theoretical maximum push is 513 kgf at 1.0 MPa. The operating pressure range is 0.15-1.0 MPa.
The M20x1.5 screw shortens the extend endpoint from the 80 mm maximum down to 50 mm; retract remains full stroke. The built-in magnet works with AirTAC reed or electronic switches for position sensing, while the screw acts only as a mechanical stop, not a mid-stroke lock.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.