
The AirTAC SDAJ80~100 Adjustable Super Slim Cylinder SDAJ80X90-30S is a genuine double-acting COMPACT cylinder (Ø80mm bore) whose extend end-position is set by an external M20×1.5 adjustment screw. You can dial the stroke anywhere from 60 to 90 mm on the machine — no shims, no part change.
The AirTAC SDAJ80X90-30S is a compact double-acting double-rod cylinder engineered for high-force applications where the extend end-position must be dialed in on the machine. An external M20x1.5 adjuster screw lets you shorten the outward stroke anywhere within a 60 to 90 mm window without swapping shims or parts.
Housed within a short riveted body, this unit saves substantial axial mounting depth compared to conventional round-body alternatives, fitting seamlessly into tight high-tonnage machinery. The bore dictates a robust 25 mm piston rod and a PT3/8 air port. End-of-travel shock is managed solely by a fixed NBR bumper, which decelerates the load but is not an adjustable air cushion. Equipped with a built-in magnet (-S), the cylinder supports AirTAC reed or electronic solid-state switches for precise position confirmation.
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ80X90-30S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Max stroke | 90 mm |
| Adjustable range | 60 – 90 mm |
| Adjuster thread (R) | M20×1.5 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M14×1.5 F / M22×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2268 N | 2268 N |
| 0.7 MPa | 3175 N | — |
| Max (@1.0 MPa) | 463 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×90 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Adapt large manufacturing fixtures rapidly by adjusting the extend stop from 90 mm down to 60 mm on the machine floor, accommodating varied product heights efficiently.
Choose this specific model if your fixture requires heavy thrust but frequent on-site stroke tuning between 60 and 90 mm.
Confirm your parameters match the SDAJ80X90-30S code: an 80 mm bore, 90 mm maximum stroke, 30 mm adjustment window, PT3/8 porting, and a female M14x1.5 rod-end thread. The included -S magnet enables switch sensing, while the male-thread variant would require a -B suffix. Remember that a plain compact cylinder cannot hold a load if air pressure drops or the valve centers; the fixed bumper only decelerates near the end of travel. For suspended loads, integrate an external rod lock or a pilot-operated check valve.
Quick checklist
At 0.7 MPa, push increases to 3518.6 N and pull to 3175 N. The theoretical maximum push is 513 kgf at 1.0 MPa.
The external M20x1.5 screw mechanically shortens the extend stroke anywhere between 60 and 90 mm without affecting force. The -S option denotes a built-in piston magnet designed to trigger AirTAC reed or electronic switches for end-position sensing.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.