Airtac SED Double Rod Cylinder SED50X800S
The AirTAC SED Double Rod Cylinder SED50X800S is a genuine double-acting ISO 15552 double-rod cylinder: a Ø20mm piston rod exits BOTH ends of the Ø50mm bore, giving equal force and speed in both directions and letting you mount tooling or a sensor flag on the back rod. Stroke 800mm, PT1/4 ports, adjustable cushioning.
- BoreØ50 mm
- Stroke800 mm
- Port sizePT1/4
- ConfigurationDouble rod
- Rod threadM16×1.5
- CushionAdjustable, 30 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SED Double Rod Cylinder SED50X800S
The AirTAC SED50X800S is a double-acting, double-rod profile cylinder built to ISO 15552 dimensional standards. Because a 20mm rod exits both end covers, the annulus area is identical on both sides, yielding exactly 825 N of output force at 0.5 MPa in both extend and retract directions.
Equipped with a standard magnet (-S), this unit drives CMSE reed or DMSE electronic sensors. The extruded aluminum barrel omits external tie rods, and the adjustable air cushions at both ends tame the kinetic energy of this long 800mm stroke.
Airtac SED Double Rod Cylinder SED50X800S Technical Specifications
| Model | Airtac SED Double Rod Cylinder SED50X800S |
|---|---|
| Series | SED ISO 15552 double-rod cylinder |
| Bore size | Ø50 mm |
| Stroke | 800 mm |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SED datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø50mm)
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 825 N |
| 0.7 MPa | 1155 N |
| Max (@1.0 MPa) | 168 kgf |
Because a rod exits both ends, the effective piston area — and therefore the force — is identical on extend and retract. Actual usable force is lower than theoretical; size with a safety margin.
Model Code: Airtac SED Double Rod Cylinder SED50X800S
| SED | ISO 15552 profile-barrel DOUBLE-ROD double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×800 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SED): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SE (single rod), SEJ (double-rod adjustable stroke), BSED (double-rod rod lock).
Where the Airtac SED Double Rod Cylinder SED50X800S Is Used
Web Guiding Mechanism
Drives a 825 N both-way correction carriage for film or foil webs, using the rear rod end to mount a tensioner cam.
Dual-Side Pallet Pusher
Pushes 800mm stroke pallets off a line, utilizing the twin rods to prevent rotational twisting under offset loads.
Transfer Shuttle Sync
Synchronizes a 50mm bore transfer arm between two machining stations, providing equal 825 N force in both travel directions.
Is the Airtac SED Double Rod Cylinder SED50X800S the Right Cylinder?
Select this 50mm bore when you need 825 N both-way force at 0.5 MPa; step down to the 40mm bore for 528 N, or up to the 63mm bore for 1402 N. The twin-rod design provides superior anti-rotation stability and allows mounting a rear cam or secondary tool. At 800mm, side loads are severe—use external guide rails to prevent rod binding. For direct replacements, match the 50mm bore, 800mm stroke, PT1/4 port, and mounting. Note: air cushions decelerate near stroke end but do not hold position on air loss; use an external pilot check valve for fail-safe holding.
Quick checklist
- ✓ Equal force/speed both directions needed?
- ✓ Back-rod space for tooling or a flag
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Support both rod ends; avoid side load.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SED Double Rod Cylinder SED50X800S FAQ
Because the double-rod design has equal piston area on both sides, output force is identical in both directions: 825 N at 0.5 MPa, 1154 N at 0.7 MPa, and a maximum of 168 kgf at 1.0 MPa.
The twin rods provide equal force and speed in both directions, improve load stability against rotation, and allow the rear rod end to drive a secondary mechanism or sensor flag. It uses a standard PT1/4 port and M16x1.5 rod thread.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SED Cylinders
Request a Quote for Airtac SED Double Rod Cylinder SED50X800S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.