verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SEJ Series · ISO 15552 Adjustable-Stroke Cylinder

Airtac SEJ Adjustable Cylinder SEJ100X200-40S

The AirTAC SEJ Adjustable Cylinder SEJ100X200-40S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 40mm window, so this Ø100mm unit covers an effective stroke of 160–200mm without changing cylinders. Force is equal in both directions.

  • BoreØ100 mm
  • Nominal stroke200 mm
  • Adjust window40 mm
  • Effective stroke160–200 mm
  • Port sizePT1/2
  • CushionAdjustable, 36 mm
$226.09 $233.59Save 3% Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SEJ100 stroke, mounting and version on one page All SEJ100 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac SEJ Adjustable Cylinder SEJ100X200-40S

The AirTAC SEJ100X200-40S is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, yielding identical annulus areas so thrust matches on extend and retract. You dial the retract stop screw up to 40 mm, setting an effective stroke range of 160 to 200 mm for exact machine commissioning. Output is 3681 N each way at 0.5 MPa.

This 100 mm bore actuator features a Ø25 mm rod, M20x1.5 end thread, and PT1/2 ports. The extruded aluminum barrel has no external tie rods. Field-adjustable air cushions at both ends decelerate the load near stroke end. The -S magnet enables CMSE reed or DMSE electronic sensors for end-position feedback.

Airtac SEJ Adjustable Cylinder SEJ100X200-40S Technical Specifications

ModelAirtac SEJ Adjustable Cylinder SEJ100X200-40S
SeriesSEJ ISO 15552 adjustable-stroke cylinder
Bore sizeØ100 mm
Nominal stroke200 mm
Adjustment window40 mm (160–200 mm)
ConfigurationDouble rod, double acting
Port sizePT1/2
Rod threadM20×1.5
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm

Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 40mm window. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø100mm)

PressureForce (both directions)
0.5 MPa3682 N
0.7 MPa5154 N
Max (@1.0 MPa)751 kgf

A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.

Model Code: Airtac SEJ Adjustable Cylinder SEJ100X200-40S

SEJISO 15552 double-rod double-acting cylinder with adjustable stroke.
100Bore size in mm.
×200Nominal stroke length in mm.
-40Adjustment stroke window in mm (options: 10/20/30/40/50/75/100).
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).

Where the Airtac SEJ Adjustable Cylinder SEJ100X200-40S Is Used

precision_manufacturing

Press Tonnage Calibration

Dial the 40 mm retract window to set exact bottom-dead-center on a 100 mm bore press, leveraging 5153 N at 0.7 MPa to form sheet metal precisely.

swap_horiz

Packaging Changeover

Adjust the effective stroke from 160 to 200 mm to match varying carton sizes on a packaging line, using the equal both-way force to push and pull the folding mechanism.

settings

Stop Block Alignment

Fine-tune the mechanical end position during machine commissioning by turning the back-rod stop screw, locking it once the conveyor diverter gate hits the exact mark.

Is the Airtac SEJ Adjustable Cylinder SEJ100X200-40S the Right Cylinder?

Confirm this 40 mm window covers your end-position tuning before locking the back-rod stop screw. If you need less force, the 80 mm bore delivers 2268 N both ways at 0.5 MPa; if you need more, the 125 mm bore provides 5734 N. For fixed-retract setups without fine-tuning, a standard SED cylinder is sufficient. A plain SEJ does not hold position on air loss; the cushion only decelerates, so specify an external rod lock for fail-safe holding. Dimensional interchangeability is guaranteed per ISO 15552.

Quick checklist

  • ✓ Need on-machine stroke fine-tuning?
  • ✓ Adjustment window (40mm) covers your range
  • ✓ Equal force both directions OK
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Set the stop screw within the 40mm window; lock it after adjusting.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SEJ Adjustable Cylinder SEJ100X200-40S FAQ

The retract stroke is adjustable up to 40 mm via a stop screw on the back rod. This gives an effective stroke range of 160 to 200 mm, which you lock in place after setting the exact end position.

Because the double-rod design yields equal annulus areas, force is identical both directions: 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Request a Quote for Airtac SEJ Adjustable Cylinder SEJ100X200-40S

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SEJ100X200-40S and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.