
The AirTAC SEJ Adjustable Cylinder SEJ100X250-100 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 100mm window, so this Ø100mm unit covers an effective stroke of 150–250mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X250-100 is a double-acting, double-rod ISO 15552 profile cylinder with a 100 mm mechanical stroke-adjustment window. A stop screw on the rear rod lets you dial the retract end from 150 mm up to the full 250 mm nominal stroke, perfect for fine-tuning a machine end position without swapping hardware. Because a rod exits both ends, the annulus area is identical in both directions, yielding equal force and speed—delivering 3681 N each way at 0.5 MPa.
This 100 mm bore unit runs on a PT1/2 port and features a Ø25 mm rod with an M20x1.5 thread. It includes field-adjustable air cushions at both ends to decelerate heavy loads near the stroke limits. Note this SKU lacks a piston magnet, so it will not trigger CMSE or DMSE position sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X250-100 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 250 mm |
| Adjustment window | 100 mm (150–250 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 100mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×250 | Nominal stroke length in mm. |
| -100 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 150-250 mm pressing depth on an assembly press.
Actuate sorting gates on a conveyor line where the retract position changes for various carton sizes. The double-rod design ensures consistent 3681 N retract force at 0.5 MPa across the entire adjustment window.
Set hard mechanical end stops for machining fixtures that switch between part families. The rear stop screw locks down precisely, avoiding the need to physically swap out a 250 mm cylinder for shorter strokes.
Verify the 100 mm adjustment window covers your required positioning range; this cylinder trims the retract stroke anywhere from 150 to 250 mm. If you need less force, the 80 mm bore provides 2268 N at 0.5 MPa, while stepping up to the 125 mm bore yields 5734 N at 0.5 MPa. If you never need to alter the end position after commissioning, a fixed-stroke SED cylinder is a simpler choice. Remember that the adjustable cushion and stop screw decelerate the load but do not hold position on air loss; for fail-safe holding, specify a BSED or an external rod lock. At 250 mm stroke, ensure external guides support the load to prevent side-loading on the rod.
Quick checklist
A stop screw on the rear rod mechanically limits the retract stroke. You can adjust the effective stroke anywhere from 150 mm up to the full 250 mm. Once you set the desired end position, you lock the screw in place on the machine.
Because it is a double-rod cylinder, the force is identical in both directions. It provides 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.