
The AirTAC SEJ Adjustable Cylinder SEJ100X50-40S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 40mm window, so this Ø100mm unit covers an effective stroke of 10–50mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X50-40S is a double-acting, double-rod ISO 15552 profile cylinder featuring an adjustable stroke. A rod exits both ends, ensuring equal force in both directions at 3681 N each way at 0.5 MPa. The retract stroke is mechanically tunable via a back-rod stop screw over a 40 mm window, yielding an effective stroke range of 10 to 50 mm.
This extruded aluminum barrel design includes field-adjustable air cushions at both ends to manage deceleration near the stroke limits. Equipped with a magnet (-S), it supports CMSE reed and DMSE electronic sensors for position feedback. The PT1/2 port and M20x1.5 rod thread match standard 100 mm bore hardware.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X50-40S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 50 mm |
| Adjustment window | 40 mm (10–50 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 40mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×50 | Nominal stroke length in mm. |
| -40 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 10 to 50 mm clamping reach on a stamping press, using the 5153 N of both-way force at 0.7 MPa to hold the workpiece securely.
Adjust the retract stop on the fly to match varying carton heights, leveraging the equal double-rod force for consistent folding pressure.
Set precise mechanical end stops for diverter gates on a conveyor, using the back-rod lock screw to dial the exact position and the M20x1.5 thread for mounts.
This 100 mm bore cylinder provides 3681 N of both-way force at 0.5 MPa. If your application requires less force, the adjacent 80 mm bore provides 2268 N, while stepping up to the 125 mm bore yields 5734 N at the same pressure. The 40 mm adjustment window is ideal for fine-tuning a machine end position during commissioning without swapping hardware. If you only need a fixed reach, a standard SED double-rod cylinder is sufficient. Note that the adjustable cushion and stop screw decelerate the load but do not hold position on air loss; for fail-safe holding, use an external rod lock or BSED. Because the stroke is under 300 mm, side-load stress is minimal, but external guides are recommended for heavy loads.
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke over a 40 mm window. You can dial the effective stroke from 10 mm up to 50 mm, then lock the screw in place for consistent positioning.
Because the rod exits both ends, the annulus area is identical in both directions. It delivers 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.