
The AirTAC SEJ Adjustable Cylinder SEJ100X500-100S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 100mm window, so this Ø100mm unit covers an effective stroke of 400–500mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X500-100S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 100mm adjustable stroke window. A rear stop screw lets you dial in the retract end from 400mm up to the full 500mm, perfect for fine-tuning end positions directly on the machine without swapping hardware. Because a rod exits both ends, the annular area is identical in both directions, yielding an equal force of 3681 N each way at 0.5 MPa.
This 100mm bore variant integrates a magnet for CMSE reed or DMSE electronic sensors. It uses a PT1/2 port, a Ø25mm rod with an M20x1.5 thread, and field-adjustable air cushions at both ends to manage deceleration over the 36mm cushion length. Note that the stop screw sets the mechanical end only; it does not hold position on air loss.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X500-100S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 500 mm |
| Adjustment window | 100 mm (400–500 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 100mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×500 | Nominal stroke length in mm. |
| -100 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 400-500mm retract stop to set varying press depths for different stamping blanks, using the equal 5153 N retract force at 0.7 MPa to pull the platen back securely.
Adjust the retract window on the fly to match diverter heights for changing carton sizes, while the double-rod design resists rotational twist during the 500mm travel.
Commission a multi-station indexer by micro-adjusting the mechanical end stop to hit exact kinematic positions without reprogramming the machine controller.
This 100mm bore delivers 3681 N both ways at 0.5 MPa (5153 N at 0.7 MPa). If your load is lighter, step down to the 80mm bore (2268 N at 0.5 MPa); for heavier drives, step up to the 125mm bore (5734 N at 0.5 MPa). If you do not need variable end-positioning, a fixed-stroke SED is sufficient. For fail-safe load holding on air loss, use an external rod lock. With a 500mm stroke, mount external guides to prevent side-load wear on the seals. ISO 15552 interchangeability means it matches by bore, stroke, 100mm window, PT1/2 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
A stop screw on the back rod mechanically shortens the retract stroke over a 100mm window. You can dial the effective stroke anywhere from 400mm to the full 500mm, then lock it in place. This only sets the end position; it is not a brake.
Because the double-rod design creates equal annular areas, force is identical both ways: 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.