
The AirTAC SEJ Adjustable Cylinder SEJ100X500-75S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø100mm unit covers an effective stroke of 425–500mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X500-75S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 75 mm adjustable retract window. You can dial the effective stroke down from 500 mm to a 425 mm minimum, allowing precise on-machine end-position tuning without hardware changes. The extruded aluminum barrel contains no external tie rods, ensuring a clean profile that is dimensionally interchangeable per ISO 15552.
Because a rod exits both ends, the annular area is symmetrical and delivers equal force in both directions: about 3681 N each way at 0.5 MPa and 5153 N at 0.7 MPa. The included -S magnet supports CMSE reed and DMSE electronic sensors for position feedback. A stop screw on the back rod mechanically sets the end point, which you lock after dialing in your target position.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X500-75S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 500 mm |
| Adjustment window | 75 mm (425–500 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×500 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 425-500 mm retract stop to perfectly match varying sheet metal blank widths, using the 5153 N both-way force to push and pull the heavy feed carriage.
Set the exact 425 mm retracted end-point for delicate component seating, locking the back-rod stop screw after commissioning to ensure repeatable 751 kgf max pressing.
Confirm this 75 mm adjustment window covers your required end-position variance (effective stroke 425-500 mm). If you need less force, the adjacent 80 mm bore yields 2268 N at 0.5 MPa both ways; if you need more, step up to the 125 mm bore for 5734 N at 0.5 MPa. If your application never requires stroke changes after commissioning, a fixed-stroke SED cylinder is sufficient. For replacement matching, verify your 100 mm bore, 500 mm stroke, PT1/2 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2). At 500 mm stroke, the extended rod is prone to bending under lateral loads—ensure external guides support the load to prevent side-load damage. A plain SEJ does not hold position on air loss; the adjustable cushion only decelerates near stroke end, so specify a BSED or external rod lock for fail-safe holding.
Quick checklist
A stop screw on the rear protruding rod lets you mechanically shorten the retract stroke by up to 75 mm. This gives an effective stroke range of 425-500 mm, which you lock in place after finding the exact end position.
Because it is a double-rod design, force is equal in both directions: 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.