
The AirTAC SEJ Adjustable Cylinder SEJ100X65-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø100mm unit covers an effective stroke of 45–65mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X65-20S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 20mm adjustable stroke window. A rod exits both ends, meaning the annulus area is identical in both directions, yielding an equal force of 3681 N each way at 0.5 MPa. You can dial the retract end from 45 to 65 mm to perfectly match a mechanical stop.
This bore uses a PT1/2 port and a Ø25 mm rod with an M20x1.5 thread. The included -S magnet supports CMSE reed and DMSE electronic sensors for end-of-stroke detection. Adjustable air cushions at both ends decelerate the load near the stroke limits, while the back-rod stop screw lets you lock the final end position precisely during machine commissioning.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X65-20S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 65 mm |
| Adjustment window | 20 mm (45–65 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×65 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 45-65mm retract distance for a 751 kgf max press fit, locking the back-rod stop screw once the bearing seat is perfectly seated.
Swap the retract stop up to 20mm to accommodate different part heights on a conveyor line, leveraging the 5153N both-way force at 0.7MPa for reliable retraction.
Fine-tune the tool engagement depth on an end-mill fixture during commissioning, using the equal push and pull forces to maintain stable cutting dynamics.
This 20mm adjustment window is ideal if you need to fine-tune a 45 to 65 mm end position on the machine without swapping hardware. If you do not need variable stops, a fixed-stroke SED is sufficient. For sizing, the neighbouring bore down (80mm) provides 2268 N both ways at 0.5 MPa, while stepping up to 125mm yields 5734 N. The SEJ100X65-20S delivers 3681 N at 0.5 MPa and 5153 N at 0.7 MPa.
Remember that the air cushion and mechanical stop screw decelerate the load and set the end position, but they do not hold position on air loss; for fail-safe holding, use an external rod lock or BSED. When replacing an ISO 15552 cylinder, match the 100mm bore, 65mm nominal stroke, PT1/2 port, and your mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2). Because the stroke is short, side loading is minimal, but always ensure the rod end thread M20x1.5 aligns cleanly with your load to prevent binding.
Quick checklist
The 20mm adjustment window lets you mechanically dial the retract stroke from 45mm up to 65mm. You set the exact end position using a stop screw on the back rod, then lock it in place.
Because the rod exits both ends, the force is identical in both directions: 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.