
The AirTAC SEJ Adjustable Cylinder SEJ100X70-40 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 40mm window, so this Ø100mm unit covers an effective stroke of 30–70mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X70-40 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 40 mm mechanical stroke adjustment. A stop screw on the rear rod lets you dial the retract end position, yielding an effective stroke range of 30 to 70 mm. This allows precise on-machine tuning without swapping hardware.
Because a rod exits both ends, the annulus area is identical in both directions, delivering an equal force of 3681 N each way at 0.5 MPa. The extruded aluminum barrel has no external tie rods, and adjustable air cushions at both ends decelerate the 25 mm rod near stroke end. This SKU omits the magnet, so it does not support CMSE or DMSE position sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X70-40 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 70 mm |
| Adjustment window | 40 mm (30–70 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 40mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×70 | Nominal stroke length in mm. |
| -40 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 40 mm retract window to perfectly set the 3681 N clamping position on varying stamping die heights during setup.
Adjust the effective stroke from 30 to 70 mm to rapidly switch carton folding stops without replacing the cylinder hardware.
Fine-tune the double-rod extension endpoint to maintain precise electrode contact distance on multi-part welding fixtures.
Verify the 40 mm adjustment window covers your required end-position variance, giving a 30 to 70 mm effective range. If you need less force, stepping down to the 80 mm bore provides 2268 N at 0.5 MPa, while stepping up to the 125 mm bore yields 5734 N. If the exact stroke is fixed and never changes, a standard SED double-rod cylinder is sufficient.
For ISO 15552 replacement matching, confirm the 100 mm bore, 70 mm nominal stroke, PT1/2 port, and your required mounting from the SEJ set (Basic, FA, LB, TC, FTC, TCM1, TCM2). Note that the adjustable cushion only decelerates the load; a plain SEJ does not hold position on air loss, so use an external rod lock for fail-safe holding.
Quick checklist
The mechanical stop screw on the back rod provides a 40 mm adjustment window. This reduces the 70 mm nominal stroke down to a minimum effective stroke of 30 mm, allowing you to set the exact retract end position on the machine.
Because the rod exits both ends, force is equal in both directions: 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.