
The AirTAC SEJ Adjustable Cylinder SEJ100X700-30S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø100mm unit covers an effective stroke of 670–700mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X700-30S is a double-acting, double-rod ISO 15552 profile cylinder with a 30 mm adjustable stroke window, letting you dial the retract end from 670 to 700 mm. A rod exits both ends, generating identical force in both directions—about 3681 N each way at 0.5 MPa. The extruded aluminum barrel contains no external tie rods, ensuring clean integration.
You mechanically set the retract position via a stop screw on the back rod, then lock it to match your machine datum precisely. This 100 mm bore version features a PT1/2 port, a Ø25 mm rod with an M20x1.5 thread, and includes a magnet for CMSE or DMSE sensors. Field-adjustable air cushions at both ends absorb kinetic energy near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X700-30S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 700 mm |
| Adjustment window | 30 mm (670–700 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×700 | Nominal stroke length in mm. |
| -30 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Delivering 3681 N both ways to drive a coil feed stop. The 30 mm window fine-tunes the 700 mm retract to sync material length during press commissioning.
Shifts a diverter between two pallet heights. The double-rod equal force and adjustable 670-700 mm end position adapt the line without swapping hardware.
Cycles an industrial machine guard. The back rod carries a cam for DMSE sensors while the stop screw sets the exact open position.
Verify the 30 mm adjustment window covers your end-position tolerance. If you need less thrust, the 80 mm bore delivers 2268 N at 0.5 MPa; if scaling up, the 125 mm bore provides 5734 N. If you never change stroke length after commissioning, a fixed-stroke SED avoids the adjustment hardware. For a 700 mm stroke, external guides are recommended to manage side loads on the Ø25 mm rod.
The adjustable stop screw and air cushions only decelerate the load near stroke end; they do not hold position on air loss. For fail-safe holding, use an external rod lock. This cylinder is dimensionally interchangeable per ISO 15552—match the 100 mm bore, 700 mm stroke, PT1/2 port, and mounting (Basic, FA, LB, TC, FTC, TCM1, TCM2) for direct replacement.
Quick checklist
A stop screw on the rear rod lets you mechanically shorten the retract stroke by up to 30 mm. For this 700 mm model, the effective stroke range is 670 to 700 mm. You lock the screw after setting the exact end position.
Because it is a double-rod cylinder, force is equal in both directions: 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.