
The AirTAC SEJ Adjustable Cylinder SEJ100X75-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø100mm unit covers an effective stroke of 55–75mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X75-20S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 20mm adjustable stroke window. A rear stop screw lets you mechanically dial the retract stroke from 55mm up to 75mm, enabling precise end-position tuning directly on the machine without swapping hardware.
This bore 100mm unit uses a PT1/2 port and a Ø25mm rod with an M20x1.5 thread. The integrated -S magnet supports CMSE reed and DMSE electronic sensors for position feedback. Adjustable air cushions at both ends decelerate the load near stroke end, while the mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2) omits FB and CA options.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X75-20S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 75 mm |
| Adjustment window | 20 mm (55–75 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×75 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 55-75mm retract stroke to match new part heights during press die setups, using the 5153 N at 0.7 MPa to consistently pull heavy tooling.
Fine-tune the clamping end-point on an assembly line during commissioning, locking the rear stop screw once the 3681 N at 0.5 MPa seats the component perfectly.
Adjust the retract distance on the fly for conveyor diverters handling different package sizes, leveraging the equal both-way force for smooth push and pull cycles.
Verify the 20mm adjustment window covers your required 55-75mm effective stroke range for commissioning or part-changeover tasks. If you need less force, stepping down to bore 80 yields 2268 N at 0.5 MPa; if you need more, moving up to bore 125 provides 5734 N both ways. If the exact end position is fixed and never changes, a standard SED double-rod cylinder is sufficient. For position holding on air loss, note this cylinder does not lock—use an external rod lock or BSED. As an ISO 15552 dimensionally interchangeable profile cylinder, confirm your replacement matches the 75mm stroke, 20mm window, PT1/2 port, and magnet options.
Quick checklist
The rear stop screw provides a 20mm adjustment window, allowing the effective retract stroke to be dialed from 55mm up to the nominal 75mm. You set the exact end-position mechanically and lock it in place.
Because the rod exits both ends, force is identical in both directions: 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.