
The AirTAC SEJ Adjustable Cylinder SEJ100X75-30S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø100mm unit covers an effective stroke of 45–75mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X75-30S is a double-acting, double-rod ISO 15552 profile cylinder with a 30 mm adjustable retract window, yielding an effective stroke range of 45-75 mm. A rod exits both ends, providing identical annulus areas and equal thrust in both directions at 3681 N each way at 0.5 MPa. The integrated -S magnet supports CMSE reed and DMSE electronic sensors for exact end-of-travel detection.
A stop screw on the back rod mechanically shortens the retract position, which is ideal for dialing in a precise stop during machine commissioning. The extruded aluminum barrel has no external tie rods, and field-adjustable air cushions at both ends decelerate the load near the stroke ends without acting as a mechanical lock.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X75-30S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 75 mm |
| Adjustment window | 30 mm (45–75 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×75 | Nominal stroke length in mm. |
| -30 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 30 mm retract window to precisely set sheet metal feed lengths in stamping presses, utilizing the 3681 N both-way force to halt heavy coil stock reliably.
Adjust the effective stroke between 45 and 75 mm to accommodate different carton sizes on packaging lines without swapping out the entire cylinder assembly.
Fine-tune the clamping end position during robotic welding commissioning, using the equal double-rod force to ensure consistent joint closure across varying material thicknesses.
This 100 mm bore provides 3681 N of both-way force at 0.5 MPa. If your application requires less force, the neighboring 80 mm bore yields 2268 N; if you need more power, stepping up to the 125 mm bore provides 5734 N at the same pressure. The 30 mm adjustment window is highly effective for fine-tuning end positions on the machine without machining new hardware. For direct ISO 15552 replacement, verify the 75 mm nominal stroke, PT1/2 port, and required mounting accessory (Basic, FA, LB, TC, FTC, TCM1, or TCM2). If a fixed end position is sufficient and you do not need field adjustability, a standard SED double-rod cylinder is a simpler alternative. Note that a plain SEJ does not hold position on air loss; for fail-safe holding, consider a BSED rod lock.
Quick checklist
The retract end features a mechanical stop screw on the back rod that provides a 30 mm adjustment window. You can dial the effective stroke down from the nominal 75 mm to a minimum of 45 mm to perfectly match your machine's end stop.
Because it is a double-rod cylinder, the force is identical in both directions: 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.