
The AirTAC SEJ Adjustable Cylinder SEJ100X80-10 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 10mm window, so this Ø100mm unit covers an effective stroke of 70–80mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X80-10 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 10 mm mechanical stroke adjustment. A rod exits both ends, yielding identical annulus areas and an equal drive force of 3681 N each way at 0.5 MPa. You turn a stop screw on the rear rod to set the retract end, giving an effective stroke range of 70 to 80 mm.
This unit carries a Ø25 mm rod with an M20x1.5 thread and PT1/2 ports. The extruded aluminum barrel omits external tie rods for a clean profile. Adjustable air cushions at both ends decelerate the 751 kgf maximum load near stroke end, while the rear rod can mount a cam or flag for external tracking.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X80-10 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 80 mm |
| Adjustment window | 10 mm (70–80 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 10mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×80 | Nominal stroke length in mm. |
| -10 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 10 mm retract window to perfectly align a 100 mm bore press die, using the equal 5153 N both-way force to seat heavy parts without offsetting the tooling.
Adjust the retract stop from 70 to 80 mm when switching carton sizes on a packaging line, letting the double-rod output push and pull identical loads at 0.5 MPa.
Fine-tune the end position during robotic welding setup, relying on the 36 mm adjustable air cushion to safely decelerate the 751 kgf maximum load before the stop screw.
Confirm this 10 mm adjustment window covers your positioning tolerance. If you need less force, the 80 mm bore delivers 2268 N at 0.5 MPa; stepping up to 125 mm provides 5734 N. If your end position never changes after commissioning, a fixed-stroke SED offers the same double-rod output without the adjustment hardware.
This SKU lacks a magnet, so it cannot host CMSE or DMSE sensors without changing the code. The air cushion and stop screw decelerate and set the mechanical end, but a plain SEJ will not hold position on air loss—specify an external rod lock for fail-safe holding. For a direct ISO 15552 replacement, match the 80 mm stroke, 10 mm window, PT1/2 port, and your required mounting from Basic, FA, LB, TC, FTC, TCM1, or TCM2.
Quick checklist
The rear stop screw provides a 10 mm adjustment window. You can mechanically dial the retract stroke from 70 mm up to the nominal 80 mm, then lock the screw in place for fixed production runs.
Because the rod exits both ends, force is identical in both directions: 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.