
The AirTAC SEJ Adjustable Cylinder SEJ100X80-10S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 10mm window, so this Ø100mm unit covers an effective stroke of 70–80mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X80-10S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 10mm adjustable stroke window, letting you dial the retract end from 70mm to 80mm. The barrel is extruded aluminum with no external tie rods, and the -S magnet enables position detection.
A stop screw on the back rod mechanically sets the exact retract position, which you lock in place after fine-tuning the machine. The cylinder includes field-adjustable air cushions at both ends to decelerate the load near stroke end, operating at speeds of 30-800 mm/s. It uses a PT1/2 port and a 25mm rod with an M20x1.5 thread.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X80-10S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 80 mm |
| Adjustment window | 10 mm (70–80 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 10mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×80 | Nominal stroke length in mm. |
| -10 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 70-80mm press depth for bearing insertion during machine commissioning, leveraging the 5153 N retract force at 0.7 MPa to seat parts without over-stressing.
Quickly adjust the retract stop by up to 10mm to accommodate different assembly stack heights on a packaging line, using the equal both-way force for stable lifting.
Test and lock the optimal clamping end-position on a machining fixture, relying on the 751 kgf maximum force and the back-rod stop screw to hold the mechanical setting.
Confirm this 10mm adjustment window covers your required 70-80mm end-position range. If you need less force, stepping down to the 80mm bore yields 2268 N at 0.5 MPa both ways, while stepping up to the 125mm bore provides 5734 N. If your end position never changes after commissioning, a fixed-stroke SED offers the same double-rod symmetry without the adjustment hardware. Remember that the air cushion and mechanical stop screw decelerate the load and set the end point, but a plain SEJ does not hold position on air loss; for fail-safe holding, use an external rod lock.
When replacing an ISO 15552 cylinder, match the 100mm bore, 80mm nominal stroke, PT1/2 port, and your mounting choice from the SEJ subset (Basic, FA, LB, TC, FTC, TCM1, TCM2). The -S magnet supports CMSE reed and DMSE electronic sensors for exact position feedback. Because the stroke is under 300mm, side-load stress is minimal, but always ensure the external guide supports any heavy lateral loads.
Quick checklist
The stop screw on the back rod provides a 10mm adjustment window, allowing you to set the effective retract stroke anywhere from 70mm to the nominal 80mm. You lock the screw in place once the exact end-position is dialed in on the machine.
Because the rod exits both ends, the force is identical in both directions. It provides 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.