
The AirTAC SEJ Adjustable Cylinder SEJ32X175-50 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø32mm unit covers an effective stroke of 125–175mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X175-50 is a double-acting, double-rod ISO 15552 profile cylinder with a 50 mm adjustable stroke window. A rod exits both ends, yielding equal force in both directions—delivering 345 N each way at 0.5 MPa. You can dial the retract end from 125 mm up to the 175 mm nominal stroke.
A mechanical stop screw on the back rod sets the exact end position, which you lock down after fine-tuning. This 32 mm bore unit features a PT1/8 port, a 12 mm rod, and adjustable air cushions at both ends to decelerate the load near stroke end. This SKU omits the magnet, so it does not support CMSE or DMSE position sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X175-50 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 175 mm |
| Adjustment window | 50 mm (125–175 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×175 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 50 mm window to match part variations precisely. The 345 N both-way force at 0.5 MPa securely shifts the diverter gate without overshooting.
Adjust the retract stroke from 125 to 175 mm when switching box sizes. The double-rod design maintains equal push and pull force for consistent flap folding.
Fine-tune the mechanical stop screw during setup to set exact crimp depth. The stop screw locks the position, while the adjustable air cushion decelerates the 12 mm rod at stroke end.
Verify the 50 mm adjustment window covers your required end-position range. If you need less force, step down is not an option below 32 mm, but if you need more, the 40 mm bore provides 528 N at 0.5 MPa. If you never need to vary the stroke after commissioning, a fixed-stroke SED saves complexity. Remember, the adjustable cushion and stop screw decelerate the load but do not hold position on air loss; use an external rod lock for fail-safe holding. For this 175 mm stroke, ensure external guides manage side loads to protect the 12 mm rod. When replacing an ISO 15552 cylinder, match the 32 mm bore, port PT1/8, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2).
Quick checklist
The 50 mm adjustment window lets you mechanically dial the retract stroke from 125 mm up to the 175 mm nominal stroke. You set the exact end position using a stop screw on the back rod, then lock it in place.
Because the rod exits both ends, force is identical in both directions. This 32 mm bore cylinder outputs 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.