
The AirTAC SEJ Adjustable Cylinder SEJ32X200-30 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø32mm unit covers an effective stroke of 170–200mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X200-30 is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, ensuring identical annulus areas and equal force in both directions—delivering 345 N each way at 0.5 MPa. A stop screw on the back rod provides a 30 mm adjustable stroke window, allowing you to dial in the retract end position to achieve an effective stroke range of 170 to 200 mm.
This design eliminates the need to swap hardware when fine-tuning end positions during machine commissioning. The extruded aluminum barrel omits external tie rods, and the field-adjustable air cushions at both ends decelerate the 12 mm rod near stroke end. This base SKU ships without a magnet, so it does not support CMSE or DMSE position sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X200-30 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 200 mm |
| Adjustment window | 30 mm (170–200 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×200 | Nominal stroke length in mm. |
| -30 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 170-200 mm retract position for an adhesive dispensing nozzle, using the 30 mm back-rod adjustment to match varying part heights without changing cylinders.
Leverage the equal 345 N both-way force to drive a small gripper assembly, fine-tuning the mechanical stop during machine commissioning to prevent overtravel.
Adjust the retract stroke on a packaging flap tucker to accommodate different carton sizes on the fly, locking the back-rod screw once the new end position is set.
Verify that the 30 mm adjustment window covers your required end-position variance, yielding a 170 to 200 mm effective stroke. If your application requires less force, no smaller SEJ bore exists, so this 32 mm bore is the baseline. If you need higher thrust, stepping up to the 40 mm bore yields 528 N at 0.5 MPa both ways, while stepping down is not an option. If your positioning never changes after commissioning, a fixed-stroke SED cylinder provides the same double-rod stability without the adjustment mechanism.
For a direct ISO 15552 replacement, match the 32 mm bore, 200 mm nominal stroke, PT1/8 port, and your required mounting bracket from the SEJ set (Basic, FA, LB, TC, FTC, TCM1, TCM2—note that FB, CA, CB, and CR mounts are omitted). The adjustable air cushion is strictly for end-of-stroke deceleration and is not a mechanical lock; this cylinder will not hold position on air loss, so consider an external rod lock for fail-safe holding.
Quick checklist
A stop screw on the rear rod lets you mechanically shorten the retract stroke by up to 30 mm. This gives an effective stroke range of 170 to 200 mm. You set the exact end position on the machine and lock the screw in place.
Because it is a double-rod cylinder, the force is identical in both directions: 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.