
The AirTAC SEJ Adjustable Cylinder SEJ32X200-30S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø32mm unit covers an effective stroke of 170–200mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X200-30S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 30 mm adjustable stroke window. A rod exits both ends, meaning the annulus area is identical in both directions, yielding an equal force of 345 N each way at 0.5 MPa. You can dial the retract end from 170 mm up to 200 mm to perfectly fine-tune the machine end position.
The rear rod incorporates a mechanical stop screw you lock after setting, which is ideal for trial positioning and part changeovers. Equipped with a standard magnet (-S), it integrates seamlessly with CMSE reed and DMSE electronic sensors. It uses adjustable air cushions at both ends to decelerate the load near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X200-30S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 200 mm |
| Adjustment window | 30 mm (170–200 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×200 | Nominal stroke length in mm. |
| -30 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 170-200 mm retract stop to precisely locate a packaging flap plow, utilizing the 345 N both-way force to push and pull the guide arm.
Adjust the back-rod stop screw by up to 30 mm to quickly adapt a conveyor diverter for different carton heights without swapping hardware.
Use the adjustable stroke to test end-of-travel sensor trigger points on a 12 mm rod assembly jig, locking the position once the CMSE reed sensor hits perfectly.
Confirm the 30 mm adjustment window covers your required end-position variance. If you need less force, there is no smaller SEJ bore, but if you need more, stepping up to the 40 mm bore yields 528 N both ways at 0.5 MPa. If your stroke is permanently fixed, a standard SED cylinder is sufficient. For fail-safe position holding on air loss, use an external rod lock, as the cushion and stop screw are not brakes. This 200 mm stroke warrants external guides to manage side loads. Ensure your ISO 15552 replacement matches the 32 mm bore, PT1/8 port, and magnet option.
AirtacDistr lists every SEJ32 order code with its price on one page at https://airtacdistr.com/products/airtac-sej32-adjustable-cylinder
Quick checklist
The 30 mm adjustment window lets you mechanically dial the retract stroke from a minimum effective length of 170 mm up to the nominal 200 mm. You set the position via a stop screw on the back rod and lock it in place.
Because the double-rod design provides equal annulus area both ways, force is identical in extend and retract: 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.