
The AirTAC SEJ Adjustable Cylinder SEJ32X200-75S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø32mm unit covers an effective stroke of 125–200mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X200-75S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 75 mm adjustable stroke window, yielding an effective stroke range of 125 to 200 mm. A rod exits both ends, making the annulus area identical in both directions for equal force and speed. This bore 32 mm unit generates 345 N each way at 0.5 MPa.
The retract end uses a mechanical stop screw on the back rod to dial in the precise end position during machine commissioning. The barrel is extruded aluminum with no external tie rods, and the -S magnet option enables CMSE reed or DMSE electronic sensors for end-of-stroke detection.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X200-75S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 200 mm |
| Adjustment window | 75 mm (125–200 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×200 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Apply 345 N of equal both-way clamping force on machined brackets, dialing the 75 mm stroke window to accommodate different part heights without swapping hardware.
Adjust the retract end from 125 to 200 mm to quickly reposition a stop or pusher when switching between product families on a packaging conveyor.
Fine-tune the end-of-travel position during R&D testing, locking the back-rod stop screw exactly where the 483 N @0.7 MPa force meets the test specimen.
This 32 mm bore provides 345 N of both-way force at 0.5 MPa. If your application requires less force, there is no smaller SEJ bore. If you need more clamping or press force, stepping up to the 40 mm bore yields 528 N each way at 0.5 MPa. If your positioning never changes after initial setup, a fixed-stroke SED cylinder is sufficient.
The 75 mm adjustment window is ideal for matching varying part heights during changeovers. Remember that the adjustable air cushion at both ends only decelerates the load near stroke end; it is not a lock. A plain SEJ will not hold position on air loss, so for fail-safe holding, use an external rod lock. As an ISO 15552 cylinder, it matches standard bore, stroke, port PT1/8, and mounting footprints.
Quick checklist
The 75 mm adjustment window allows you to mechanically dial the retract stroke from a minimum effective stroke of 125 mm up to the nominal 200 mm. You set the exact end position with a stop screw on the back rod and lock it in place.
Because the rod exits both ends, the force is identical in both directions. It provides 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.