
The AirTAC SEJ Adjustable Cylinder SEJ32X210-75S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø32mm unit covers an effective stroke of 135–210mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X210-75S is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, ensuring identical annulus area for equal force and speed in both directions—delivering 345 N each way at 0.5 MPa. The retract stroke is mechanically adjustable via a stop screw on the back rod over a 75 mm window, yielding an effective stroke range of 135 to 210 mm.
This unit includes a magnet for CMSE reed or DMSE electronic sensors. It features field-adjustable air cushions at both ends for end-of-stroke deceleration. Note that the cushion and stop screw set the mechanical end; they do not hold position on air loss.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X210-75S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 210 mm |
| Adjustment window | 75 mm (135–210 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×210 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 135-210 mm stroke to clamp varying part heights on a machining fixture, using the 345 N both-way force to secure components securely.
Adjust the retract end-stop during production line changeovers to accommodate different product lengths without swapping hardware.
Fine-tune the end position during R&D prototype testing, locking the back-rod stop screw precisely when the optimal travel is found.
Confirm the 75 mm adjustment window covers your required positioning range. If 345 N at 0.5 MPa is insufficient, stepping up to the 40 mm bore yields 528 N both ways; if less force is acceptable, there is no smaller standard SEJ bore. A fixed-stroke SED is sufficient if you do not need on-machine end-position tuning. For fail-safe load holding, use an external rod lock. Since the 210 mm stroke exceeds 300 mm only marginally, external guides are recommended to prevent side-load wear on the 12 mm rod. Replacement matches ISO 15552 dimensions, PT1/8 port, and the basic mounting set.
Quick checklist
The retract stroke is adjustable up to 75 mm via a stop screw on the back rod. The effective stroke range is 135 to 210 mm, allowing precise on-machine end-position tuning.
Because it is a double-rod cylinder, force is equal in both directions: 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.