
The AirTAC SEJ Adjustable Cylinder SEJ32X250-10 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 10mm window, so this Ø32mm unit covers an effective stroke of 240–250mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X250-10 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 10mm adjustable stroke window, letting you dial the retract end from 240mm to 250mm. A rod exits both ends, generating identical extend and retract forces of 345N at 0.5 MPa and 483N at 0.7 MPa. The back-rod stop screw sets the mechanical end for precise positioning, while field-adjustable air cushions at both ends decelerate the payload near stroke end.
This 32mm bore unit uses a PT1/8 port, a 12mm rod with an M10x1.25 thread, and runs at speeds of 30-800 mm/s. Because it lacks a magnet, this specific SKU does not support CMSE or DMSE position sensing. The extruded aluminum barrel omits external tie rods, and the mounting set covers Basic, FA, LB, TC, FTC, TCM1, and TCM2.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X250-10 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 250 mm |
| Adjustment window | 10 mm (240–250 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 10mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×250 | Nominal stroke length in mm. |
| -10 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 10mm retract window to perfectly match varying part heights on a pick-and-place gantry without swapping hard stops, using 483N of equal both-way force.
Fine-tune the 240-250mm effective stroke on an electronic assembly press to dial in precise bearing insertion depths during machine commissioning.
Adjust the rear stop screw to accommodate different carton formats on a packaging line, shifting the end position within the 10mm window for rapid format changes.
Verify the 10mm adjustment window covers your required end-position variance; if you need a broader fine-tuning range, consider a larger -20 or -30 adjust code. Sizing both ways: stepping down to a 25mm bore is not standard for this series, while stepping up to a 40mm bore yields 528N at 0.5 MPa. If your application requires a fixed 250mm stroke without mechanical dialing, the SED double-rod cylinder is a simpler choice. Remember that the stop screw and air cushions only set the mechanical end and decelerate motion; they do not hold position on air loss. For fail-safe holding, use an external rod lock. At 250mm stroke, ensure external guides support side loads to prevent rod binding.
As a dimensionally interchangeable ISO 15552 cylinder, replacing a unit requires matching the 32mm bore, 250mm nominal stroke, 10mm adjust window, PT1/8 port, and mounting style.
Quick checklist
A stop screw on the back rod mechanically shortens the retract stroke over a 10mm window. You can dial the effective stroke from 240mm up to 250mm. Once set, lock the screw to maintain the exact end position.
Because the rod exits both ends, the force is identical in both directions: 345N at 0.5 MPa, 483N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.