
The AirTAC SEJ Adjustable Cylinder SEJ32X30-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø32mm unit covers an effective stroke of 10–30mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X30-20S is a double-acting, double-rod ISO 15552 profile cylinder with an adjustable retract stroke. A rod exits both ends, yielding identical annulus areas so output force is equal in both directions at 345 N each way at 0.5 MPa. The integrated -20 stop screw lets you mechanically dial the retract end position across a 20 mm window, setting the effective stroke anywhere from 10 mm to 30 mm.
Because the rear rod protrudes, overall length is longer than a single-rod unit, but it provides a convenient mounting point for a cam or flag. This bore uses a PT1/8 port, a 12 mm rod with an M10x1.25 thread, and includes a magnet for position sensing. The extruded aluminum barrel contains no external tie rods, and adjustable air cushions at both ends decelerate the 30-800 mm/s travel near the stroke extremes.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X30-20S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 30 mm |
| Adjustment window | 20 mm (10–30 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×30 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 10-30 mm retract stop to perfectly match varying cardboard thicknesses, applying 345 N of equal both-way force without changing hardware.
Use the protruding rear rod to mount a cam for a DMSE electronic sensor, fine-tuning the 10-30 mm contact stroke during machine commissioning.
Adjust the retract end position on the fly to shift a 32 mm bore diverting gate between different product widths on a packaging line.
Verify the 20 mm adjustment window covers your positioning range; here you can fine-tune the retract stop anywhere from 10 mm up to the full 30 mm. If 345 N at 0.5 MPa is insufficient, stepping up to the 40 mm bore yields 528 N both ways; if you need less force, there is no smaller standard SEJ bore, so a smaller compact cylinder format might be required. If the end position never changes after commissioning, a fixed-stroke SED saves complexity. Remember that the stop screw and air cushions only set the mechanical end and decelerate motion; they do not hold position on air loss, so an external rod lock is needed for fail-safe holding. When replacing an ISO 15552 unit, match the 32 mm bore, 30 mm nominal stroke, PT1/8 port, and your chosen mounting from the SEJ set (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
The -20 designation means the retract end has a 20 mm adjustment window. You can dial the effective stroke down from the 30 mm nominal to a minimum of 10 mm, allowing precise end-position tuning on the machine.
Because a rod exits both ends, the annular area is identical in both directions. It generates 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa, equal for both extend and retract.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.