
The AirTAC SEJ Adjustable Cylinder SEJ32X350-40S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 40mm window, so this Ø32mm unit covers an effective stroke of 310–350mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X350-40S is a double-acting, double-rod ISO 15552 profile cylinder offering equal force in both directions, delivering 345 N at 0.5 MPa. A rod exits both ends, meaning the annulus area is identical for extend and retract strokes. You can dial the retract end up to 40 mm via a stop screw on the back rod, yielding an effective stroke range of 310-350 mm.
This extruded aluminum barrel design features field-adjustable air cushions at both ends to manage deceleration over the long travel. The included -S magnet enables precise end-position detection with CMSE reed or DMSE electronic sensors. It operates at speeds from 30-800 mm/s with a PT1/8 port and a 12 mm rod end.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X350-40S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 350 mm |
| Adjustment window | 40 mm (310–350 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 40mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×350 | Nominal stroke length in mm. |
| -40 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 40 mm window to fine-tune the retraction stop on conveyor edge-guides, matching varying board widths without swapping hardware.
Adjust the 310-350 mm effective stroke on the fly when shifting carton sizes, using the equal 345 N both-way force to push and pull forming plates.
Set precise trial end-positions for liquid dispensing heads, leveraging the -S magnet and DMSE sensors to verify the exact adjusted stroke endpoint.
Confirm this 40 mm adjustment window covers your required end-position variance. For sizing, the next bore down is 32 mm (this unit, providing 345 N both ways at 0.5 MPa), while stepping up to a 40 mm bore yields 528 N. If your application never requires stroke changes, a fixed-stroke SED saves space and cost. Remember, the adjustable cushion and stop screw decelerate the load but do not hold position on air loss; use an external rod lock for fail-safe holding. Because the 350 mm stroke is long, ensure external guides manage side loads to prevent rod binding.
AirtacDistr lists every SEJ32 order code with its price on one page at https://airtacdistr.com/products/airtac-sej32-adjustable-cylinder
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke by up to 40 mm. This gives an effective stroke range of 310-350 mm, allowing you to fine-tune the machine end-position during commissioning. You lock the screw after setting your desired position.
Because it is a double-rod cylinder, the force is identical in both directions. It provides 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.