
The AirTAC SEJ Adjustable Cylinder SEJ32X450-20 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø32mm unit covers an effective stroke of 430–450mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X450-20 is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, yielding identical annulus areas so output force is equal in both directions at 345 N (0.5 MPa). The retract stroke is mechanically adjustable via a stop screw on the back rod over a 20 mm window, giving an effective stroke range of 430-450 mm.
This unit features a PT1/8 port, a 12 mm rod with an M10x1.25 thread, and field-adjustable air cushions at both ends. Because it lacks a magnet (-S), it cannot host CMSE or DMSE sensors. The extruded aluminum barrel provides ISO 15552 dimensional interchangeability without external tie rods.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X450-20 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 450 mm |
| Adjustment window | 20 mm (430–450 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×450 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 430-450 mm retract stop to precisely trim circuit board edges during commissioning, utilizing the 345 N both-way force for clean cuts.
Fine-tune the end position to accommodate varying carton heights without swapping hardware, relying on equal push and pull forces.
Transition a 32 mm bore actuator between product families by adjusting the mechanical stop screw to match new part heights.
Confirm the 20 mm adjustment window covers your required end-position variance. For sizing, the next bore down is 32 mm itself (345 N at 0.5 MPa), while stepping up to a 40 mm bore yields 528 N both ways at 0.5 MPa. If you require a fail-safe hold on air loss, this cylinder cannot lock; use a BSED or external rod lock. At 450 mm stroke, external guides are recommended to prevent rod side-loading. Match ISO replacements by bore, stroke, 20 mm window, port, and mounting (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
The retract stroke is adjustable via a back-rod stop screw over a 20 mm window, resulting in an effective stroke range of 430 to 450 mm. Lock the screw after setting your desired end position.
Because the rod exits both ends, force is identical in both directions: 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.