
The AirTAC SEJ Adjustable Cylinder SEJ32X50-40FA is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 40mm window, so this Ø32mm unit covers an effective stroke of 10–50mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X50-40FA is a double-acting, double-rod ISO 15552 profile cylinder with an FA front foot mount. A rod exits both ends, yielding identical annulus areas so output force is equal in both directions at 345 N each way at 0.5 MPa. A stop screw on the back rod lets you mechanically dial the retract stroke down by 40 mm, setting an effective stroke range of 10 to 50 mm.
Because it lacks the -S option, this specific SKU has no internal magnet and cannot host CMSE or DMSE position sensors. The extruded aluminum barrel omits external tie rods for a clean profile, and adjustable air cushions at both ends decelerate the 12 mm rod near stroke ends without acting as a mechanical lock.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X50-40FA |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 50 mm |
| Adjustment window | 40 mm (10–50 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 40mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×50 | Nominal stroke length in mm. |
| -40 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 10 to 50 mm retract window to precisely set a fluid dispenser probe height, utilizing the equal 345 N both-way force for stable contact.
Adjust the back-rod stop to match different carton flap thicknesses during format changeovers without replacing the entire cylinder assembly.
Fine-tune the pickup drop position on a small transfer arm during commissioning, locking the stop screw once the exact 10-50 mm end point is proven.
Verify the 40 mm adjustment window covers your target retract position, allowing you to fine-tune the end stop on the machine without swapping hardware. If you need slightly less force, the next bore down is unavailable, but if you need to step up, the 40 mm bore provides 528 N both ways at 0.5 MPa. If your stroke never changes after commissioning, a fixed-stroke SED is sufficient.
For any fail-safe load holding, note that this cylinder will not hold position on air loss; the cushion and stop screw only set the mechanical end. When replacing an ISO 15552 cylinder, match the 50 mm nominal stroke, PT1/8 port, FA mount, and 10-50 mm effective range.
Quick checklist
The stop screw on the rear rod provides a 40 mm adjustment window. You can dial the effective retract stroke from 10 mm up to the nominal 50 mm, which is ideal for setting precise end positions on the machine.
Because the rod exits both ends, the force is identical in both directions: 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.